UCC3973PWTRG4 datasheet(4/24 Pages) TI1

Teilenummer	UCC3973PWTRG4

Bauteilbeschribung	BiCMOS Cold Cathode Fluorescent Lamp Driver Controller

Download	24 Pages

Scroll/Zoom	100%

Hersteller	TI1 [Texas Instruments]

Direct Link	http://www.ti.com

Logo

4 / 24 page

4

UCC1972/3

UCC2972/3

UCC3972/3

BUCK: Senses the voltage on the top side of the induc-

tor feeding the resonant tank. The voltage at this point

is used to synchronize the internally generated ramp

and to detect whether an open lamp condition exists.

An open lamp condition exists when this voltage is be-

low the specified threshold for seven clock cycles. If the

MODE pin is held below the open lamp detect enable

threshold, this protective feature is disabled.

On the UCC3973, this pin is also used to sense an

over-voltage across the transformer primary. If the volt-

age at this pin exceeds the clamp threshold, current will

be sourced fron the FB pin.

COMP: Output of the error amplifier.Compensation

components set the bandwidth of the entire system and

are normally connected between COMP and FB. The

error amplifier averages lamp current against a fixed in-

ternal reference. The resulting voltage on the COMP

pin is compared to an internally generated ramp, set-

ting the PWM duty cycle. During UVLO, this pin is ac-

tively pulled low.

FB: This pin is the inverting input to the error amplifier.

On the UCC3973, current is sourced form this pin if the

clamp threshold is exceeded at the BUCK pin (see be-

low). The sourced current will reduce OUT duty cycle to

control transformer primary voltage. The source current

is disabled on the UCC3972.

GND: Ground reference for the IC.

MODE: The voltage on this pin is used to control start-up

and various modes of operation for the part (refer to the ta-

ble in the block diagram).

When the voltage is below 1V, OUT is forced low, open

lamp detection is disabled and the error amplifier is

tri-stated.

When the voltage is between 1V and 3V, OUT is enabled

and the error amplifier output is connected to COMP. Open

lamp detection is still disabled and a constant 20 A current

is sourced from this pin. Placing an appropriate value ex-

ternal capacitor between this pin and ground allows the

user to disable open lamp detection for a set period of time

at start-up to allow the lamp to strike.

When MODE reaches 3V, open lamp detection is enabled

and normal operation is activated.

OUT: Drives the buck regulator N-channel MOSFET. OUT

turn-on is synchronized to twice the tank resonant fre-

quency. OUT is actively pulled low when in UVLO, an

open lamp condition has been detected or MODE is less

than 1V.

VBAT: Positive input supply to power stage. This voltage is

required by internal control circuitry to provide open-lamp

detection and synchronization. Operating range is from

4.5V to 25V.

VDD: This pin connects to the battery voltage from which

the CCFL inverter will operate. If the potential on VBAT

can exceed 18V in the application, a series resistor must

be placed between VBAT and this pin (see applications

section). The voltage at the VDD pin will then be regulated

to 18V. This pin should be bypassed with a minimum ca-

pacitance of 0.1

mF.

PIN DESCRIPTIONS

0

200

400

600

800

8.7

9.2

9.7

VBAT -VBUCK

Clamp current vs. tank voltage for UCC3973.

Ähnliche Beschreibung - UCC3973PWTRG4

Hersteller	Teilenummer	Datenblatt	Bauteilbeschribung
Texas Instruments	UCC1972	308Kb / 17P	[Old version datasheet] BiCMOS Cold Cathode Fluorescent Lamp Driver Controller
Texas Instruments	UCC1972	895Kb / 24P	[Old version datasheet] BiCMOS Cold Cathode Fluorescent Lamp Driver Controller
Monolithic Power System...	MP1010B	35Kb / 1P	Cold Cathode Fluorescent Lamp Driver
Monolithic Power System...	MP1011A	128Kb / 6P	Cold Cathode Fluorescent Lamp Driver
Texas Instruments	UCC2974	229Kb / 14P	[Old version datasheet] DUAL COLD CATHODE FLUORESCENT LAMP CONTROLLER
Texas Instruments	UCC3974	210Kb / 12P	[Old version datasheet] DUAL COLD CATHODE FLUORESCENT LAMP CONTROLLER
Dallas Semiconductor	DS3984	790Kb / 24P	4-Channel Cold-Cathode Fluorescent Lamp Controller
Maxim Integrated Produc...	DS3988	778Kb / 23P	8-Channel Cold-Cathode Fluorescent Lamp Controller Rev 0; 4/05
	DS3984	508Kb / 24P	4-Channel Cold-Cathode Fluorescent Lamp Controller Rev 1; 5/07
	DS3994	537Kb / 28P	4-Channel Cold-Cathode Fluorescent Lamp Controller Rev 0; 10/06

More results

UCC3973PWTRG4 Datenblatt(PDF) 4 Page - Texas Instruments

UCC3973PWTRG4 Datenblatt(HTML) 4 Page - Texas Instruments

Ähnliche Teilenummer - UCC3973PWTRG4

Ähnliche Beschreibung - UCC3973PWTRG4

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datenblatt Download

Link URL