8

8-41

Catalog 1654025

Dimensions are in millimeters

Dimensions are shown for

USA: 1-800-522-6752

South America: 55-11-3611-1514

Revised 12-04

and inches unless otherwise

reference purposes only.

Canada: 1-905-470-4425

Japan: 81-44-900-5102

specified. Values in brackets

Specifications subject

Mexico: 01-800-733-8926

Singapore: 65-4866-151

www.tycoelectronics.com

are U.S. equivalents.

to change.

C. America: 52-55-5-729-0425

UK: 44-1793-528171

Wire Termination to Pin/Post/Tab

Wire

Tape Carrier Spacing of Sleeves (Center-to-Center)

Terminal

1.27

2.54

3.17

4.0

Dimensions

AWG

None

[0.050]

[0.100]

[0.125]

[0.156]

W = up to 0.61 [.024]

30–26

[0.05–0.15]

D-141-30

D-713-03

—

—

—

24–22

[0.24–0.38]

D-141-07

—

D-711-00

—

—

W = 0.63 [.025] to

20

[0.61]

D-141-31

—

D-711-04

D-711-07

D-711-08

0.81 [.032]

W = 0.76 [.030] to

24–20

[0.24–0.61]

D-141-56

—

—

—

—

1.27 [.050]

W = up to 1.52 [.060]

24–20

[0.24–0.61]

D-129-05

—

D-714-01

——

W = 1.27 [.050] to

24–20

[0.24–0.61]

D-129-03

—

—

—

D-714-00

2.28 [.090]

W = 2.28 [.090] to

24–20

[0.24–0.61]

D-129-0043

—

—

—

—

3.55 [.140]

Part

Inside Diameter

Fully

No.*

As Supplied**

Recovered†

Length††

D-110-0062

1.0 [0.040]

0.6 [0.025]

16.0 [0.630]

D-110-0217

1.0 [0.040]

0.6 [0.025]

9.0 [0.360]

D-141-13

0.75 x 1.65 [0.030 X 0.065]

0.75 [0.030]

4.7 [0.185]

D-141-22

0.75 x 1.65 [0.030 X 0.065]

0.75 [0.030]

6.0 [0.240]

D-141-30

0.75 x 1.65 [0.030 X 0.065]

0.75 [0.030]

9.5 [0.375]

than 0.6 [.025] wide.

*The D-110 series sleeves are primarily for single wire terminations and do not have a wire stop. The D-141 series will

accept either one or two wires; the parts have a built-in wire stop that will locate the wire approximately 0.76 [0.03]

from bottom of terminal.

**Minimum. Wire insulation must be smaller than this. When using the D-141 parts for two-wire terminations, the com-

bined wire insulation diameters must be less than 1.5 [.060].

†Maximum. The combination of conductor diameter and terminal width and the wire insulation must be greater than

this.

††The terminal length should be at least 1.2 [0.05] shorter than this. The wire strip length must be adjusted so that,

when terminated, the exposed conductor is covered by the sleeve.

pin

W

post

W

tab

W

For Fine Wire Terminations

0.15 mm

Smaller*

Table B. D-129/141/71X Series

(up to 150°C [302°F] rated)

Connection-point

Type and Size