![]() |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
LM393SNG Datenblatt(PDF) 3 Page - ON Semiconductor |
|
|
LM393SNG Datenblatt(HTML) 3 Page - ON Semiconductor |
3 / 6 page ![]() LM393S, LM2903S http://onsemi.com 3 ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, Tlow ≤ TA ≤ Thigh, unless otherwise noted.) Characteristic Symbol LM393S LM2903S Unit Min Typ Max Min Typ Max Input Offset Voltage (Note 3) VIO mV TA = 25°C − ±1.0 ±5.0 − ±2.0 ±7.0 Tlow ≤ TA ≤ Thigh − − ±9.0 − ±9.0 ±15 Input Offset Current IIO nA TA = 25°C − ±5.0 ±50 − ±5.0 ±50 Tlow ≤ TA ≤ Thigh − − ±150 − ±50 ±200 Input Bias Current (Note 4) IIB nA TA = 25°C − 25 250 − 25 250 Tlow ≤ TA ≤ Thigh − − 400 − 200 500 Input Common Mode Voltage Range (Note 5) VICR V TA = 25°C 0 − VCC −1.5 0 − VCC −1.5 Tlow ≤ TA ≤ Thigh 0 − VCC −2.0 0 − VCC −2.0 Voltage Gain AVOL 50 200 − 25 200 − V/mV RL ≥ 15 kW, VCC = 15 Vdc, TA = 25°C Large Signal Response Time − − 200 − − 200 − ns Vin = TTL Logic Swing, Vref = 1.4 Vdc VRL = 5.0 Vdc, RL = 5.1 kW, TA = 25°C Response Time (Note 6) tTLH − 1.0 − − 1.0 − ms VRL = 5.0 Vdc, RL = 5.1 kW, TA = 25°C Input Differential Voltage (Note 7) VID − − VCC − − VCC V All Vin ≥ GND or V− Supply (if used) Output Sink Current ISink 6.0 16 − 6.0 16 − mA Vin ≥ 1.0 Vdc, Vin+ = 0 Vdc, VO ≤ 1.5 Vdc TA = 25°C Output Saturation Voltage VOL mV Vin ≥ 1.0 Vdc, Vin+ = 0, ISink ≤ 4.0 mA, TA = 25°C − 150 400 − − 400 Tlow ≤ TA ≤ Thigh − − 700 − 200 700 Output Leakage Current IOL nA Vin− = 0 V, Vin+ ≥ 1.0 Vdc, VO = 5.0 Vdc, TA = 25°C − 0.1 − − 0.1 − Vin− = 0 V, Vin+ ≥ 1.0 Vdc, VO = 30 Vdc, Tlow ≤ TA ≤ Thigh − − 1000 − − 1000 Supply Current ICC mA RL = ∞ Both Comparators, TA = 25°C − 0.6 1.0 − 0.6 1.0 RL = ∞ Both Comparators, VCC = 30 V − 0.75 2.5 − 0.75 2.5 Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. LM393S Tlow = 0°C, Thigh = +70°C LM2903S Tlow = −40°C, Thigh = +105°C 3. At output switch point, VO]1.4 Vdc, RS = 0 W with VCC from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to VCC = −1.5 V). 4. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state, therefore, no loading changes will exist on the input lines. 5. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of common mode range is VCC −1.5 V. 6. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are obtainable. 7. The comparator will exhibit proper output state if one of the inputs becomes greater than VCC, the other input must remain within the common mode range. The low input state must not be less than −0.3 V of ground or minus supply. |
Ähnliche Teilenummer - LM393SNG |
|
Ähnliche Beschreibung - LM393SNG |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |