OMAP3530ECBBA datasheet(250/265 Pages) TI1

250 / 265 page

etk_clk

etk_ctl

etk_d[15:0]

ETM0

ETM2

ETM3

ETM2

ETM1

ETM3

030-110

OMAP3530, OMAP3525

SPRS507H – FEBRUARY 2008 – REVISED OCTOBER 2013

www.ti.com

6.8

Test Interfaces

The emulation and trace interfaces allow tracing activities of the following CPUs:

•

ARM1136JF-STM through an Embedded Trace Macro-cell (ETM11) dedicated to enable real-time

trace of the ARM subsystem operations and a Serial Debug Trace Interface (SDTI)

•

IVA2 DSP through a high-speed real-time data exchange (HS-RTDX) controller

All processors can be emulated via JTAG ports.

6.8.1

Embedded Trace Macro Interface (ETM)

Table 6-142 assumes testing over the recommended operating conditions (see Figure 6-69).

Table 6-142. Embedded Trace Macro Interface Switching Characteristics(1)

NO.

PARAMETER

1.15 V

UNIT

MIN

MAX

1/tc(CLK)

Frequency, etk_clk

166

MHz

ETM0

tc(CLK)

Cycle time(2), etk_clk

ETM1

tW(CLK)

Clock pulse width, etk_clk

2.7

ETM2

td(CLK-CTL)

Delay time, etk_clk clock edge to etk_ctl transition

–0.5

0.5

ETM3

td(CLK-D)

Delay time, etk_clk clock high to etk_d[15:0] transition

–0.5

0.5

(1)

The capacitive load is equivalent to 25 pF.

(2)

Cycle time is given by considering a jitter of 5%.

Figure 6-69. Embedded Trace Macro Interface

6.8.2

System Debug Trace Interface (SDTI)

The system debug trace interface (SDTI) module provides real-time software tracing functionality to the

OMAP3530/25 device.

The trace interface has four trace data pins and a trace clock pin.

This interface is a dual-edge interface: the data are available on rising and falling edges of sdti_clk but can

be also configured in single edge mode where data are available on falling edge of sdti_clk.

Serial interface operates in clock stop regime: serial clock is not free running, when there is no trace data

there is no trace clock.

6.8.2.1

System Debug Trace Interface in Dual-Edge Mode

Table 6-144 assumes testing over the recommended operating conditions and electrical characteristic

conditions (see Figure 6-70).

250

TIMING REQUIREMENTS AND SWITCHING CHARACTERISTICS

Submit Documentation Feedback

Product Folder Links: OMAP3530 OMAP3525

OMAP3530ECBBA Datenblatt(PDF) 250 Page - Texas Instruments

OMAP3530ECBBA Datenblatt(HTML) 250 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL