HT46R46 datasheet(18/42 Pages) HOLTEK

18 / 42 page

HT46R46/HT46C46/HT46R47/HT46C47

Rev. 1.00

December 28, 2004

A/D Converter

The 4 channels and 8-bit resolution for the HT46R46/

HT46C46 or 9-bit resolution for the HT46R47/HT46C47

A/D converter are implemented in this microcontroller.

The reference voltage is VDD. The A/D converter con-

tains 3 special registers for the HT46R46/HT46C46

which are; ADR (21H), ADCR (22H) and ACSR (23H) or

contains 4 special registers for the HT46R47/HT46C47

whice are; ADRL (20H), ADRH (21H), ADCR (22H) and

ACSR (23H). The ADR is HT46R46/ HT46C46 an A/D

result register that is read-only. The ADRH and ADRL

are HT46R47/HT46C47 A/D result register higher-order

byte and lower-order byte which are read-only. After the

A/D conversion is completed, the ADR (HT46R46/

HT46C46) or ADRL, ADRH (HT46R47/HT46C47)

should be read to get the conversion result data. The

ADCR is an A/D converter control register, which de-

fines the A/D channel number, analog channel select,

start A/D conversion control bit and the end of A/D con-

version flag. If the users want to start an A/D conversion,

define PB configuration, select the converted analog

channel, and give START bit a raising edge and a falling

edge (0

®1®0). At the end of A/D conversion, the

EOCB bit is cleared and an A/D converter interrupt oc-

curs (if the A/D converter interrupt is enabled). The

ACSR is A/D clock setting register, which is used to se-

lect the A/D clock source.

The A/D converter control register is used to control the

A/D converter. The bit2~bit0 of the ADCR are used to

select an analog input channel. There are a total of four

channels to select. The bit5~bit3 of the ADCR are used

to set PB configurations. PB can be an analog input or

as digital I/O line decided by these 3 bits. Once a PB line

is selected as an analog input, the I/O functions and

pull-high resistor of this I/O line are disabled, and the

A/D converter circuit is power on. The EOCB bit (bit6 of

the ADCR) is end of A/D conversion flag. Check this bit

to know when A/D conversion is completed. The START

bit of the ADCR is used to begin the conversion of A/D

converter. Give START bit a raising edge and falling

edge that means the A/D conversion has started. In or-

der to ensure the A/D conversion is completed, the

START should stay at

²0² until the EOCB is cleared to

²0² (end of A/D conversion).

The bit 7 of the ACSR is used for testing purpose only. It

can not be used for the users. The bit1 and bit0 of the

ACSR are used to select A/D clock sources.

When the A/D conversion is completed, the A/D inter-

rupt request flag is set. The EOCB bit is set to

²1² when

the START bit is set from

²0² to ²1².

ADR

Note:

D0~D7 is A/D conversion result data bit

LSB~MSB.

ADR (21H) Register for HT46R46/HT46C46

ADRL

¾¾¾¾¾¾¾

ADRH

Note:

D0~D8 is A/D conversion result data bit

LSB~MSB.

ADRL (20H), ADRH (21H) Register for HT46R47/HT46C47

f S Y S / 2

P W M

[ P W M ] = 1 0 0

[ P W M ] = 1 0 1

P W M

[ P W M ] = 1 0 2

P W M

[ P W M ] = 1 0 3

P W M

P W M c y c l e : 2 5 6 / f S Y S

2 5 / 6 4

2 6 / 6 4

2 5 / 6 4

2 6 / 6 4

2 5 / 6 4

2 6 / 6 4

2 5 / 6 4

2 6 / 6 4

M o d u l a t i o n c y c l e 0

P W M m o d u l a t i o n p e r i o d : 6 4 / f S Y S

M o d u l a t i o n c y c l e 1

M o d u l a t i o n c y c l e 2

M o d u l a t i o n c y c l e 3

M o d u l a t i o n c y c l e 0

PWM

HT46R46 Datenblatt(PDF) 18 Page - Holtek Semiconductor Inc

HT46R46 Datenblatt(HTML) 18 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Datenblatt Download

Link URL