TAI-TECH

P3

5. Specification

Part Number

Inductance

L0 (uH)±20%

I rms ( A )

Typ

I rms ( A )

Max

I sat ( A )

Typ

I sat ( A )

Max

DCR

(mΩ) Typ.

@25℃

DCR

(mΩ) Max.

@25℃

TMPC0618H-R10YG-D

0.10±30%

18.0

16.0

45.0

40.0

2.10

2.50

TMPC0618H-R15MG-D

0.15

18.0

16.0

34.0

30.0

2.20

2.60

TMPC0618H-R15YG-D

0.15±30%

18.0

16.0

34.0

30.0

2.20

2.60

TMPC0618H-R18YG-D

0.18±30%

17.0

15.0

32.0

29.0

2.50

3.00

TMPC0618H-R22MG-D

0.22

16.0

14.0

26.0

24.0

2.50

3.00

TMPC0618H-R33MG-D

0.33

14.0

12.0

22.0

19.0

4.80

5.80

TMPC0618H-R47MG-D

0.47

12.0

10.0

18.0

16.0

6.40

7.40

TMPC0618H-R56MG-D

0.56

11.0

9.50

17.5

15.0

8.50

10.0

TMPC0618H-R68MG-D

0.68

10.0

9.00

17.0

15.0

9.50

11.0

TMPC0618H-R82MG-D

0.82

8.50

7.90

15.5

14.0

11.5

14.0

TMPC0618H-1R0MG-D

1.00

7.00

6.50

14.0

12.0

14.5

17.0

TMPC0618H-1R2MG-D

1.20

6.50

6.00

13.5

11.0

20.0

24.0

TMPC0618H-1R5MG-D

1.50

6.00

5.50

13.0

11.0

21.0

25.2

TMPC0618H-2R2MG-D

2.20

6.00

5.50

11.0

10.0

31.0

35.0

TMPC0618H-3R3MG-D

3.30

5.00

4.50

9.00

8.00

40.0

46.0

TMPC0618H-4R7MG-D

4.70

4.00

3.60

7.00

6.00

68.0

76.0

TMPC0618H-5R6MG-D

5.60

3.50

3.10

6.00

5.00

78.0

86.0

TMPC0618H-6R8MG-D

6.80

3.00

2.60

5.50

4.50

93.0

104

TMPC0618H-8R2MG-D

8.20

2.60

2.20

4.50

3.80

123

140

TMPC0618H-100MG-D

10.0

2.30

2.00

3.50

3.10

143

160

TMPC0618H-150MG-D

15.0

2.00

1.70

3.00

2.70

240

280

TMPC0618H-220MG-D

22.0

1.80

1.50

2.50

2.10

300

360

TMPC0618H-330MG-D

33.0

1.30

1.10

2.10

1.80

550

650

Note:

2. All test data referenced to 25℃ ambient.

3. Testing Instrument(or equ) : L: HP4284A,CH11025,CH3302,CH1320,CH1320S LCR METER / Rdc:CH16502,Agilent33420A MICRO OHMMETER.

4. Heat Rated Current (Irms) will cause the coil temperature rise approximately ΔT of 40℃

6. The part temperature (ambient + temp rise) should not exceed 125℃under worst case operating conditions.Circuit design,component,PCB trace size and

thickness,airflow and other cooling provisions all affect the part temperature. Part temperature should be verified in the end application.

7. Special inquiries besides the above common used types can be met on your requirement.