MODEL: W2PP

W2PP SPECIFICATIONS

ES-5534 Rev.12 Page 2/4

http://www.m-system.co.jp/

RELATED PRODUCTS

• Clamp-on pulse sensor (model: CLSP)

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3 screw terminals (torque 0.8 N·m)

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output 1 to output 2 to power

Frequency range: Input and output are the same.

Chattering protection: Filter provided for mechanical

contact input

Input pulse sensing: DC coupled

INPUT SPECIFICATIONS

Excitation: 12 V DC @30 mA; shortcircuit protection

■ Open Collector

Maximum frequency: 10 kHz

Pulse width time requirement: 10 μsec. min. for ON and OFF

Sensing: Approx. 12 V DC @3 mA

ON/OFF level: ≤ 600 Ω / 1.8 V for ON, ≥ 100 kΩ / 3.5 V for

OFF

■ Mechanical Contact

Maximum frequency: 30 Hz

Pulse width time requirement: 10 msec. min. for ON and

OFF

Sensing: Approx. 12 V DC @3 mA

ON/OFF level: ≤ 200 Ω / 0.6 V for ON, ≥ 100 kΩ / 2.5 V for

OFF

■ Voltage Pulse

Maximum frequency: 10 kHz

Pulse width time requirement: 10 μsec. min. for high and

low levels

Waveforms: Square or sine

Hi/Lo level: 2 – 50 V for high level; ≤1 V for low level

Input impedance: 10 kΩ min.

■ Clamp-on Pulse Sensor CLSP

Maximum frequency: 50 000 pulses/hour

ON/OFF level: ≤ 400 Ω / 1.3 V for ON, ≥ 200 kΩ / 12 V for

OFF

OUTPUT SPECIFICATIONS

■ Low Frequency Open Collector:

50 V DC @100 mA (resistive load)

Maximum frequency: 30 Hz

Timer: Limits within 75 ±25 msec.

for wider than 75 msec. pulses

ON time for output logic non-inverted

OFF time for output logic inverted

(When the low frequency open collector or the dry contact

AC/DC switch is selected as one of the outputs, the timer is

applied also to the other output.)

Saturation voltage: 0.5 V DC

■ High Frequency Open Collector:

50 V DC @100 mA (resistive load)

Maximum frequency: 10 kHz

Saturation voltage: 0.5 V DC

■ Voltage Pulse

Maximum frequency: 10 kHz

High level: Rating (5, 12 or 24 V) ±10 %

Low level: ≤ 0.5V

Load resistance:

≥ 250 Ω for 5 V

≥ 600 Ω for 12 V

≥ 1200 Ω for 24 V, output 1

≥ 2400 Ω for 24 V, output 2

■ Dry Contact AC/DC Switch

132 V AC @200 mA (cos ø = 1)

30 V DC @200 mA (resistive load)

Maximum frequency: 30 Hz

Timer: Limits within 75 ±25 msec.

for wider than 75 msec. pulses

ON time for output logic non-inverted

OFF time for output logic inverted

(When the low frequency open collector or the dry contact

AC/DC switch is selected as one of the outputs, the timer is

applied also to the other output.)

Saturation voltage: 3 V DC

INSTALLATION

Power Consumption

•AC:

Approx. 4 VA at 100 V

Approx. 5 VA at 200 V

Approx. 6 VA at 240 V

•DC: Approx. 4 W

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 200 g (0.44 lb)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

1 to output 2 to power to ground)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2