MODEL: DL30

DL30 SPECIFICATIONS

ES-8571 Rev.6 Page 2/11

https://www.m-system.co.jp/

• PC configurator software (model: R30CFG)

• User-defined web browser screen designing software

(model: DL30 Web Designer)

• Local certification authority creator (model: LCA-DL30)

Software downloadable at M-System’s web site.

• SD card

An SD card is required to store data in the unit.

Use an SD card of the designated model number which is

available commercially and from M-System.

- Hagiwara Solutions NSD6-016GH(B20SEI,

NSD6-004GH(B21SEI

(NSD6-004GH(A00SDI ... discontinued)

GENERAL SPECIFICATIONS

Connection

RUN contact output, power supply: M3 separable screw

terminal (torque 0.5 N·m)

Ethernet: RJ-45 modular jack

Internal bus: Via the Installation Base (model: R30BS)

Internal power supply: Via the Installation Base (model:

R30BS)

Solderless terminal: Refer to the Applicable Solderless

Terminal Size drawing.

Recommended manufacturer: Japan Solderless Terminal

MFG.Co.Ltd, Nichifu Co.,ltd

(Ones with insulation sleeve do not fit.)

Screw terminal: Nickel-plated steel

Housing material: Flame-resistant resin (gray)

Max. number of R30 I/O modules: 16

(Max. consumption current of I/O modules: 500 mA)

Isolation: Ethernet to internal bus or internal power to RUN

contact output to power supply to FE

Calendar clock: Year (4 digits), month, date, day, hour,

minute, second

Internal bus communication cycle: Approx. ≤ 1 msec. (when

max. No. of modules connected )

Status Indicator LEDs: PWR, RUN, DL30 RUN, LOGGING,

SD CARD, MAINT, ERROR

(Refer to Operating Manual for details)

■ RUN CONTACT OUTPUT

RUN contact turns ON in normal conditions, and turns OFF

when the power is not supplied or when an error occurs

(internal memory error, SD card error, or R30 module error).

Rated load: 250 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 0.5 A (resistive load)

(Less than 50 V AC to conform with EU Directive)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA (AC) or 150 W (DC)

Minimum load: 5 V DC @ 10 mA

When driving an inductive load, external contact protection

and noise quenching recommended.

■Recommended solderless terminal size - M3 (unit: mm)

12 max.

3 max.

3.2 dia.

R30 CONNECTION

■ DL30 INSTALL POSITION

Install DL30 on the R30BS using the PWR slot (the leftmost

slot) and the COM slot to the right of the PWR slot.

■ COMPATIBLE R30 SERIES MODULES

TYPE

MODEL

Base

R30BS

Discrete input

R30XN16A

Discrete output

R30YN16A

R30YN16C

DC voltage/current input

R30SV2

R30SV4

DC voltage/current input, high speed R30SVF4

DC voltage/current output

R30YV4

R30YS4

Thermocouple input

R30TS4

RTD input

R30RS4

Potentiometer input

R30MS4

AC current input

R30CT4E

Universal input

R30US2

R30US4

Totalized pulse input

R30PA2

Blank filler module

R30DM

Interface I/O module

R30GCIE1

R30GECT1

ETHERNET COMMUNICATION

Communication Standard: IEEE 802.3u

Transmission: 10BASE-T, 100BASE-TX

Baud rate: 10/100 Mbps (Auto Negotiation function)

Protocol: TCP/IP, Modbus/TCP, SLMP, HTTP, HTTPS, SMTP,

FTP, FTPS, SNTP

Transmission media: 10BASE-T (STP, Category 5) 100BASE-

TX (STP, Category 5e)

Max. segment length: 100 meters

Status Indicator LEDs: DPX, LNK

IP address: 192.168.0.1 (factory default)

INSTALLATION

Power consumption

•DC: Approx. 18 W 24 V DC (@ output current max. 500

mA)

Internal power