MAX397CSLASHD datasheet(5/14 Pages) MAXIM

5 / 14 page

(V+ = +3V ±10%, V- = 0V, GND = 0V, VAH = VENH = 2.4V, VAL = VENL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)

(V+ = +5V ±10%, V- = 0V, GND = 0V, VAH = VENH = 2.4V, VAL = VENL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)

Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in

this data sheet.

Note 3: Guaranteed by design.

Note 4: ∆RON = RON(MAX) - RON(MIN).

Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the

specified analog signal ranges, i.e., VNO = 3V to 0V and 0V to -3V.

Note 6: Leakage parameters are 100% tested at maximum rated hot operating temperature, and guaranteed by correlation at +25°C.

Note 7: Worst-case isolation is on channel 4 because of its proximity to the COM pin. Off-isolation = 20log VCOM/VNO, VCOM = output,

VNO = input to off switch.

Note 8: Leakage testing at single supply is guaranteed by correlation testing with dual supplies.

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

(Note 2) MAX

UNITS

DYNAMIC

Transition Time (Note 3)

tTRANS VNO = 3V, Figure 2

TA = +25°C

105

245

TA = TMIN to TMAX

350

Break-Before-Make Interval

tOPEN

(Note 3)

TA = +25°C

Enable Turn-On Time

(Note 3)

tON(EN)

TA = +25°C

125

200

TA = TMIN to TMAX

275

Enable Turn-Off Time

(Note 3)

tOFF(EN)

TA = +25°C

100

125

TA = TMIN to TMAX

200

Charge Injection (Note 3)

VCTE

CL = 100pF, VNO = 0V,

Figure 5

TA = +25°C

1.5

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

(Note 2) MAX

UNITS

SWITCH

Analog Signal Range

VANALOG (Note 3)

V-

V+

On-Resistance

RON

INO = 1mA, VCOM = 1.5V,

V+ = 3V

TA = +25°C

315

550

Ω

TA = TMIN to TMAX

650

DYNAMIC

Transition Time (Note 3)

tTRANS

Figure 2, VIN = 2.4V,

VN01 = 1.5V, VN08 = 0V

TA = +25°C

230

575

TA = TMIN to TMAX

750

Enable Turn-On Time

(Note 3)

tON(EN)

Figure 3, VINH = 2.4V,

VINL = 0V, VN01 = 1.5V

TA = +25°C

260

500

Enable Turn-Off Time

(Note 3)

tOFF(EN)

Figure 3, VINH = 2.4V,

VINL = 0V, VN01 = 1.5V

TA = +25°C

135

400

Charge Injection (Note 3)

VCTE

CL = 100pF, VNO = 0V,

Figure 5

TA = +25°C

MAX396/MAX397

Precision, 16-Channel/Dual 8-Channel,

Low-Voltage, CMOS Analog Multiplexers

www.maximintegrated.com

Maxim Integrated │ 5

Electrical Characteristics —Single +5V Supply (continued)

Electrical Characteristics—Single +3V Supply

MAX397C/D Datenblatt(PDF) 5 Page - Maxim Integrated Products

MAX397C/D Datenblatt(HTML) 5 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Datenblatt Download

Link URL