GaAs SPDT 2.7 V High Power Switch

DC - 3.0 GHz

MASWSS0117

M/A-COM Inc. and its affiliates reserve the right to make changes to the

product(s) or information contained herein without notice. M/A-COM makes

no warranty, representation or guarantee regarding the suitability of its

products for any particular purpose, nor does M/A-COM assume any liability

whatsoever arising out of the use or application of any product(s) or

information.

•

North America Tel: 800.366.2266 / Fax: 978.366.2266

•

Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

•

Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macom.com for additional data sheets and product information.

V2

2

2

2. For positive voltage control, external DC blocking capacitors are required on all RF ports.

3. Insertion loss can be optimized by varying the DC blocking capacitor value, e.g. 1000 pF for 100 MHz - 1 GHz, 39 pF for 0.5 - 3 GHz.

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Insertion Loss

3

DC – 1 GHz

1 – 2 GHz

2 - 3 GHz

dB

dB

dB

—

—

—

0.30

0.35

0.35

0.65

—

—

Isolation

DC – 1 GHz

1 – 2 GHz

2 - 3 GHz

dB

dB

dB

23

—

—

25

19

15

—

—

—

Return Loss

DC – 3 GHz

dB

—

20

—

IP3

825 MHz

Two Tone, +24 dBm Total Pin, 5 MHz Spacing

dBm

—

56

—

Cross Modulation

For Cell Band: Two-tone signal input: Tx1 = +22 dBm @

820 MHz, Tx2 = +22 dBm @ 821 MHz,

RX interfere = -23 dBm @ 869 MHz.

dBm

—

-99

—

For PCS Band: Two-tone signal input: Tx1 = +18 dBm @

1880 MHz, Tx2 = +18 dBm @ 1881 MHz,

RX interfere = -23 dBm @ 1960 MHz.

dBm

—

-94

—

P0.1dB

1.0 GHz

dBm

—

38

—

Trise, Tfall

10% to 90% RF, 90% to 10% RF

nS

—

70

—

Ton, Toff

50% control to 90% RF

50% control to 10% RF

nS

—

100

—

Transients

In Band

mV

—

25

—

Control Current

µA

—

5

20

Parameter

Absolute Maximum

Input Power

(0.5 - 3 GHz, 3 V Control)

+38 dBm

Operating Voltage

+8.5 volts

Operating Temperature

-40°C to +85°C

Storage Temperature

-65°C to +150°C

6. For positive voltage control, external DC blocking capacitors

are required on all RF ports.

7. Differential voltage, V (state 1) - V (state 0), must be +2.7 V

minimum, but must not exceed 8.5 V.

8. 0 = -5 V to +2.3 V, 1 = -2.3 V to +5 V.

V1

V2

ANT– RF1

ANT - RF2

1

0

On

Off

0

1

Off

On

4. Exceeding any one or combination of these limits may cause

permanent damage to this device.

5. M/A-COM does not recommend sustained operation near

these survivability limits.