HA5013IP datasheet(2/14 Pages) INTERSIL

2 / 14 page

Absolute Maximum Ratings

Thermal Information

Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V

DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±V

SUPPLY

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V

Output Current (Note 2) . . . . . . . . . . . . . . . . Short Circuit Protected

ESD Rating (Note 4)

Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . 2000V

Operating Conditions

Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC

Supply Voltage Range (Typical) . . . . . . . . . . . . . . . .

±4.5V to ±15V

Thermal Resistance (Typical, Note 1)

JA (

oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

120

Maximum Junction Temperature (Die Only, Note 3). . . . . . . . . 175oC

Maximum Junction Temperature (Plastic Package, Note 3) . . 150oC

Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

θJA is measured with the component mounted on an evaluation PC board in free air.

2. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle)

output current should not exceed 15mA for maximum reliability.

3. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175oC for die, and below 150oC

for plastic packages. See Application Information section for safe operating area information.

4. The non-inverting input of unused amplifiers must be connected to GND.

Electrical Specifications

VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤10pF, Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

(NOTE 9)

TEST

LEVEL

TEMP.

(oC)

MIN

TYP

MAX

UNITS

INPUT CHARACTERISTICS

Input Offset Voltage (VIO)

A25

0.8

AFull

Delta VIO Between Channels

Full

1.2

3.5

Average Input Offset Voltage Drift

Full

µV/oC

VIO Common Mode Rejection Ratio

VCM = ±2.5V (Note 5)

Full

VIO Power Supply Rejection Ratio

±3.5V ≤ V

S ≤ ±6.5V

AFull

Input Common Mode Range

VCM = ±2.5V (Note 5)

Full

±2.5

Non-Inverting Input (+IN) Current

µA

AFull

µA

+IN Common Mode Rejection

(+IBCMR =)

VCM = ±2.5V (Note 5)

A25

0.15

µA/V

AFull

0.5

µA/V

+IN Power Supply Rejection

±3.5V ≤ V

S ≤ ±6.5V

0.1

µA/V

AFull

0.3

µA/V

Inverting Input (-IN) Current

25, 85

µA

A-40

µA

Delta - IN BIAS Current Between Channels

25, 85

µA

A-40

µA

+RIN

HA5013

HA5013IP Datenblatt(PDF) 2 Page - Intersil Corporation

HA5013IP Datenblatt(HTML) 2 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Datenblatt Download

Link URL