TUSB8042AI datasheet(16/64 Pages) TI2

16 / 64 page

7.3 Feature Description

7.3.1 Battery Charging Features

The TUSB8042A provides support for USB Battery Charging (BC1.2) and custom charging. Battery charging

support can be enabled on a per port basis through the REG_6h(batEn[3:0]) or the BATEN[4:1] pins.

USB Battery charging support includes both Charging Downstream Port (CDP) and Dedicated Charging Port

(DCP) modes. The DCP mode is compliant with the Chinese Telecommunications Industry Standard YD/T

1591-2009. CDP is enabled when the upstream port has detected valid VBUS, configured, and host sets port

power. When the upstream port is not connected and battery charging support is enabled, the TUSB8042A

enables DCP mode once all other battery modes such as ACPx have failed or are disabled.

In addition to USB Battery charging (BC1.2), the TUSB8042A supports custom charging indications: Divider

Charging (ACP3, ACP2, ACP1 modes), and Galaxy compatible charging. These custom charging modes are

only supported when upstream port is unconnected and AUTOMODE is enabled. AUTOMODE can be enabled

either thru AUTOENz pin or from Reg_0Ah bit 1 (autoModeEnz) . When in AUTOMODE and upstream port is

disconnected, the port automatically transitions from ACP mode to the DCP mode depending on the portable

device connected. The divided mode places a fixed DC voltage on the ports DP and DM signals which allows

some devices to identify the capabilities of the charger. The default divider mode indicates support for up to 10W

(ACP3). The divider mode can be configured to report a lower-current setting (up to 5 W) through REG_0Ah

(HiCurAcpModeEn).

When the upstream port is not connected and battery charging support is enabled for a port, the TUSB8042A

drives the port power enable active. If AUTOMODE is disabled, then DCP mode is used. If AUTOMODE is

enabled and fully automatic mode is disabled (FullAutoEn bit is cleared (Reg_25h Bit 0) or FULLAUTOz pin = 0),

then TUSB8042A starts with highest enabled divider current mode (ACPx). The TUSB8042A remains in highest

current mode as long as a pullup is not detected on DP pin. If an pullup is detected on DP pin, then TUSB8042A

drives the port power enable inactive and switch to Galaxy mode, if enabled, or to DCP mode if Galaxy mode is

disabled. The TUSB8042A again drives the port power enable active. The TUSB8042A remains in Galaxy mode

as long as no pullup is detected on DP pin. If an pullup is detected on DP pin, then TUSB8042A drives the port

power enable inactive and transition to DCP mode. The TUSB8042A again drives the port power enable active.

In DCP mode, the TUSB8042A looks for a pullup detected on DP pin or RxVdat. If a pullup or RxVdat is detected

on DP, the TUSB8042A remains in DCP mode. If no pullup or RxVdat is detected on DP pin after 2 seconds,

the TUSB8042A drives the port power enable inactive and transition back to ACPx mode. This sequence repeats

until upstream port is connected.

When Automatic mode is enabled and full automatic mode is enabled (FullAutoEn Reg_25h bit 0 is set or

FULLAUTOz pin = 1), TUSB8042A performs same sequence described in previous paragraph with the addition

of attempting all supported ACPx modes before sequencing to Galaxy Mode (if enabled) or DCP mode.

The supported battery charging modes when TUSB8042A configured for SMBus or external EEPROM is

detailed in Table 7-1.

The supported battery charging modes when TUSB8042A configured for I2C but without an external EEPROM is

determined by the sampled state of the pins. These modes are detailed in Table 7-2.

TUSB8042A

SLLSF93A – JUNE 2019 – REVISED JANUARY 2025

www.ti.com

Submit Document Feedback

Product Folder Links: TUSB8042A

TUSB8042AI Datenblatt(PDF) 16 Page - Texas Instruments

TUSB8042AI Datenblatt(HTML) 16 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Datenblatt Download

Link URL