FZ-SSLASHSC datasheet(37/54 Pages) OMRON

37 / 54 page

FH-Series

Components and Functions

* Use the attachment power terminal connector (male) of FH-XCN series.

For details, refer to 5-3 Sensor Controller Installation on Vision System FH series Hardware Setup Manual (Z366).

Name

Description

[1]

POWER LED

Lit while power is ON.

[2]

ERROR LED

Lit when an error has occurred.

[3]

RUN LED

Lit while the layout turned on output setting is displayed.

[4]

ACCESS LED

Blinks while the internal nonvolatile memory is accessed.

[5]

SD POWER LED

Blinks while power is supplied to the SD memory card and the card is usable.

[6]

SD BUSY LED

Blinks while the SD memory card is accessed.

[7]

EtherCAT RUN LED

Lit while EtherCAT communications are usable.

[8]

EtherCAT LINK/ACT IN LED

Lit when connected with an EtherCAT device, and blinks while performing communications.

[9]

EtherCAT LINK/ACT OUT LED

Lit when connected with an EtherCAT device, and blinks while performing communications.

[10]

EtherCAT ERR LED

Lit when EtherCAT communications have become abnormal.

[11]

EtherNet NET RUN1 LED

Lit while EtherNet communications are usable.

[12]

EtherNet LINK/ACK1 LED

Lit when connected with an EtherNet device, and blinks while performing communications.

[13]

EtherNet NET RUN2 LED

Lit when EtherNet communications are usable.

[14]

EtherNet LINK/ACK2 LED

Lit when connected with an EtherNet device, and blinks while performing communications.

Name

Description

SD memory card installation connector

Install the SD memory card. Do not plug or unplug the SD memory card during measurement operation.

Otherwise measurement time may be affected or data may be destroyed.

EtherNet connector

Connect an EtherNet device.

USB connector

Connect a USB device. Do not plug or unplug it during measurement operation.

Otherwise measurement time may be affected or data may be destroyed.

RS-232C connector

Connect an external device such as a programmable controller.

DVI-I connector

Connect a monitor.

I/O connector (control lines, data lines)

Connect the controller to external devices such as a sync sensor and PLC.

EtherCAT address setup volume

Used to set a node address (00 to 99) as an EtherCAT communication device.

EtherCAT communication connector (IN)

Connect the opposed EtherCAT device.

EtherCAT communication connector (OUT) Connect the opposed EtherCAT device.

Encoder connector

Connect an encoder.

Camera connector

Connect cameras.

Power supply terminal connector

Connect a DC power supply. Wire the controller independently on other devices. Wire * the ground line.

Be sure to ground the controller alone.

[7]

[8]

[9]

[10]

[1]

[2]

[3]

[4]

[5]

[6]

[11]

[12]

[13]

[14]

Sensor Controllers

High-speed,

Large-capacity Controller

Standard Controller

(4-camera type)

FH-2050 Series/FH-5

@50 Series

Upper port:

Ethernet port

Lower port:

Ethernet port, EtherNet/IP

port, and PROFINET port

are sharing use.

FZ-S/SC Datenblatt(PDF) 37 Page - Omron Electronics LLC

FZ-S/SC Datenblatt(HTML) 37 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Datenblatt Download

Link URL