 |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
|
Datenblatt-Suchmaschine für elektronische Bauteile |
|
M38041FFHKP Datenblatt(PDF) 70 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M38041FFHKP Datenblatt(HTML) 70 Page - Renesas Technology Corp |
|
|
70 / 387 page  1-52 REJ09B0212-0100Z Rev.1.00 Jan 14, 2005 3804 Group (Spec.H) HARDWARE FUNCTIONAL DESCRIPTION 2. Notes when selecting clock asynchronous serial I/O 2.1 Stop of transmission operation q Note Clear the transmit enable bit to “0” (transmit disabled). The trans- mission operation does not stop by clearing the serial I/O3 enable bit to “0”. q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to “1” at this time, the data during internally shifting is output to the TxD3 pin and an operation failure occurs. 2.2 Stop of receive operation q Note Clear the receive enable bit to “0” (receive disabled). 2.3 Stop of transmit/receive operation q Note 1 (only transmission operation is stopped) Clear the transmit enable bit to “0” (transmit disabled). The trans- mission operation does not stop by clearing the serial I/O3 enable bit to “0”. q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to “1” at this time, the data during internally shifting is output to the TxD3 pin and an operation failure occurs. q Note 2 (only receive operation is stopped) Clear the receive enable bit to “0” (receive disabled). s Notes concerning serial I/O3 1. Notes when selecting clock synchronous serial I/O 1.1 Stop of transmission operation q Note Clear the serial I/O3 enable bit and the transmit enable bit to “0” (serial I/O and transmit disabled). q Reason Since transmission is not stopped and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins TxD3, RxD3, SCLK3, and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O enable bit is set to “1” at this time, the data during internally shifting is output to the TxD3 pin and an operation failure occurs. 1.2 Stop of receive operation q Note Clear the receive enable bit to “0” (receive disabled), or clear the serial I/O3 enable bit to “0” (serial I/O disabled). 1.3 Stop of transmit/receive operation q Note Clear both the transmit enable bit and receive enable bit to “0” (transmit and receive disabled). (when data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception can- not be stopped.) q Reason In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and re- ception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also oper- ates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to “0” (transmit disabled). Also, the transmission circuit is not initialized by clear- ing the serial I/O3 enable bit to “0” (serial I/O disabled) (refer to 1.1). |
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
German ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
