+

+

Tel: 954 .717 .4155

Fax: 954

Web: www.luminis.com.

Sept. 2006

Toll free: 888 .401 .6999

Luminaires may be altered for design improvements or discontinued without prior notice.

OPTIONS

Electrical controls

Quartz restrike standby lamp kit.

When power failure is restored, it

will energize temporary Quartz

lamp with progressive dimming

until full H.I.D light output is

produced.

max.100w DC bayonet type.

(Lamp is not included.)

Not Applicable with CFL lamps.

Quartz lamp restrike

Option: QRS

Quartz lamp emergency socket

Quartz lamp socket for external

120V emergency power input.

Separate 120V dedicated wiring is

included.

max.100 W DC bayonet type.

(Lamp is not included.)

Not Applicable with CFL lamps.

Option: QS

Pulse start ballast

Use of pulse start lamp and ballast combination

requires a lens enclosure with the luminaire. Please

check with compatible luminaire lens option.

Note: Some pulse start lamps may be available as

protected lamp version to eliminate the lens

enclosure. If required, please contact factory to

verify availability and compatibility.

-

+

+

-

+

+

Dual switching

Luminaires ballasts

are wired for external

switching control.

DS1: Luminaires with

2 lamps individually

externally controlled.

DS2: Luminaires with

4 lamps or more are

externally controlled

by set of 2 lamps.(for

other lamp groupings,

please consult factory)

DS1

DS2

L U M I

I

N S

Electronic dimming ballast

Standard dimming ballast

MARK X 60HZ / EOL protection

Dimming;5-100% Min. start. temp. 10ºC (50ºF)

Burn lamps 100 hrs at full light output before dimming.

Page

16

Note: Add suffix PS to selected lamp wattage.

DS2: Luminaire ballast housing length

and stem size may be increased to

accomodate required number of ballasts.

Emergency battery back-up

EM42

One lamp:

26w: 450 Lmns..

32w: 575 Lmns.

42w: 750 Lmns.

Time: 90 Mnts -120/277V / T 0º C

For 57w & 70w:

(Remote installation only) Consult factory

EM242

HOT

Single pole test switch (Breaking the connection)

BLK

WHT

WHT

COM

EM

ballast

EM Ballast wiring

diagram for 120V

factory connection.

If remote test switch

is required, please

add

AC ballast

Two lamp:

26w / 32w

750 Lmns.

* EM42S

* EM242S

Note: Overall luminaire height will increase by 2” (50)

to accommodate battery back-up

Black/120V (Factory wired)

Orange/277V

(Cap unused lead.)

+

+

DS1-26:

Dual single lamp switching 26W

DS2-26:

Dual lamp switching by pair 2x26W

DS1-42:

Dual single lamp switching 32W or 42W

DS2-42:

Dual lamp switching by pair 2x32W or 2X42W

DS1-70:

Dual single lamp switching 57W or 70W

DS2-70:

Dual lamp switching by pair 2x57W or 2X70W

DS1-120:

Dual single lamp switching 85W or 120W

DS2-120:

Dual lamp switching by pair 2x85W or 2x120W

DS2-642:

Dual lamp switching by pair 2x32W or 2X42W

DS2-842:

Dual lamp switching by pair 2x32W or 2X42W

DS2-657:

Dual lamp switching by pair 2x57W or 2X70W

DM1-120

DM1-277

1X26/32/42W

DM2-120

DM2-277

2X26W

2DM2-120

2DM2-277

4X26W

DM3-120

DM3-277

2X32/42W

DM3-120

DM3-277

1X57/70W

DM4-120

DM4-277

2X57/70W

2DM3-120

2DM3-277

4X32/42W

3DM3-120

3DM3-277

6X32/42W

DM5-120

DM5-277

4X57/70W

Dimming specification

N0. of lamps

Specifying option

120V

277V

Switched luminaire wired for

external wall switch control.

To be specified if required.

Optional:

Note:

*Unless otherwise specified, test switch and indicator

light are installed with luminaires at all times.

* Standard factory prewiring for

Unswitched luminaire.

Rev.Feb.2007