HIP6301VCB datasheet(7/20 Pages) INTERSIL

7 / 20 page

FN9034.2

December 27, 2004

Absolute Maximum Ratings

Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V

Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to VCC + 0.3V

ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5KV

Recommended Operating Conditions

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V

±5%

Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C

Thermal Information

Thermal Resistance (Typical, Note 1)

θJA (°C/W)

16 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .

20 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C

Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C

(SOIC - Lead Tips Only)

CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational section of this specification is not implied.

NOTE:

θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. (See Tech Brief TB379 for details.)

2. VID input levels above 2.9V may produce an reference-voltage offset inaccuracy.

Electrical Specifications

Operating Conditions: VCC = 5V, TA = 0°C to 70°C, Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNITS

INPUT SUPPLY POWER

Input Supply Current

RT = 100kΩ

-10

EN = 0V

4.25

8.8

4.5

POR (Power-On Reset) Threshold

VCC Rising

4.25

4.38

4.5

VCC Falling

3.75

3.88

4.00

REFERENCE AND DAC

System Accuracy

Percent system deviation from programmed VID Codes

-0.8

0.8

DAC (VID0 - VID3) Input Low Voltage

DAC Programming Input Low Threshold Voltage

0.8

DAC (VID0 - VID3) Input High Voltage

DAC Programming Input High Threshold Voltage

2.0

VID Pull-Up

VIDx = 0V or VIDx = 2.5V (Note 2)

µA

CHANNEL GENERATOR

Frequency, FSW

RT = 100kΩ, ±1%

224

280

336

kHz

Adjustment Range

See Figure 10

0.05

1.5

MHz

Disable Voltage

Maximum voltage at FS/DIS to disable controller. IFS/DIS = 1mA.

1.2

1.0

ERROR AMPLIFIER

DC Gain

RL = 10K to ground

Gain-Bandwidth Product

CL = 100pF, RL = 10K to ground

MHz

Slew Rate

CL = 100pF, RL = 10K to ground

5.3

µs

Maximum Output Voltage

RL = 10K to ground

3.6

4.1

Minimum Output Voltage

RL = 10K to ground

0.16

0.5

ISEN

Full Scale Input Current

-50-

µA

Over-Current Trip Level

-82.5-

µA

POWER GOOD MONITOR

Under-Voltage Threshold

VSEN Rising

0.92

VDAC

Under-Voltage Threshold

VSEN Falling

0.90

VDAC

PGOOD Low Output Voltage

IPGOOD = 4mA

0.18

0.4

PROTECTION

Overvoltage Threshold

VSEN Rising

1.12

1.15

1.2

VDAC

HIP6301V, HIP6302V

HIP6301VCB Datenblatt(PDF) 7 Page - Intersil Corporation

HIP6301VCB Datenblatt(HTML) 7 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datenblatt Download

Link URL