LM8322 datasheet(13/42 Pages) NSC

13 / 42 page

10.7 INITIALIZATION EXAMPLE

In the following example, the LM8322 is configured as:

•

Keypad matrix configuration is 8 × 4.

•

GPIO_03 through GPIO_07 are available to use as GPIO

pins.

•

GPIO_03 is an output driven low.

•

GPIO_4 and GPIO_5 are outputs driven high.

•

GPIO_06 and GPIO_07 are inputs with weak pulldowns.

•

GPIO_14 and GPIO_15 are inputs with weak pullups.

•

The PWM clock source is the internal execution clock

divided by 64 (about 32 kHz).

Most of these settings can be verified by executing com-

mands

such

READ_CONF,

READ_PORT_SEL,

READ_CLOCK, etc.

ALL

GPIO

states

can

read

using

the

READ_PORT_STATE command, without regard to whether

the pin is an input or an output.

An open-drain signal can be created by alternating between

input mode and driving the output low.

All GPIO s can sink and source 16 mA when configured as

an output.

Command

Encoding Parameter 1 Parameter 2

Description

WRITE_CFG

0x81

0x40

Selects 36-pin package and disables the two digital

multiplexers.

WRITE_CLK

0x93

0x08

SLOWCLKOUT disabled, no external 32.768 kHz clock

required, PWM clock source is internal.

SET_KEY_SIZE

0x90

0x84

Selects a keypad matrix size of 8 × 4.

SET_ACTIVE

0x8B

0x4B

Sets the active time to about 300 milliseconds (75 × 4

milliseconds).

SET_DEBOUNCE

0x8F

0x03

Sets the key debouncing time to about 12 milliseconds

(3 × 4 ms). This is actually the default and would not have

to be performed.

WRITE_PORT_SEL

0x85

0x00

0x38

Configure GPIO_03, GPIO_04, and GPIO_05 as

outputs. Configure GPIO_06, GPIO_07, GPIO_14, and

GPIO_15 as inputs.

WRITE_PULL_DOWN

0x84

0x00

0x3F

Set the direction for the pullup/pulldown devices on

GPIO_06 and GPIO_07 to pulldown. Set the direction for

the pullup/pulldown devices on GPIO_14 and GPIO_15

to pullup.

WRITE_PORT_STATE

0x86

0xC0

0xF0

Set GPIO_04 and GPIO_05 to drive high. Enable the

pullups on GPIO_06, GPIO_07, GPIO_14, and

GPIO_15.

11.0 Halt Mode

The fully static architecture of the LM8322 allows stopping the

internal RC clock in Halt mode, which reduces power con-

sumption to the minimum level. Figure 6 shows the current in

Halt mode at the maximum V

CC (1.98V) from 25°C to +85°C.

30013606

FIGURE 6. Halt Current vs. Temperature at 1.98V

Halt mode is entered when no key-press event, key-release

event, or ACCESS.bus activity is detected for a certain period

of time (by default, 500 milliseconds). The mechanism for en-

tering Halt mode is always enabled in hardware, but the host

can program the period of inactivity which triggers entry into

Halt mode.

11.1 ACCESS.bus ACTIVITY

When the LM8322 is in Halt mode, any activity on the

ACCESS.bus interface will cause the LM8322 to exit from

Halt mode. However, the LM8322 will not be able to acknowl-

edge the first bus cycle immediately following wake-up from

Halt mode. It will respond with a negative acknowledgement,

and the host should then repeat the cycle.

The LM8322 will be prevented from entering Halt mode if it

shares the bus with peripherals that are continuously active.

For lowest power consumption, the LM8322 should only

share the bus with peripherals that require little or no bus ac-

tivity after system initialization.

LM8322 Datenblatt(PDF) 13 Page - National Semiconductor (TI)

LM8322 Datenblatt(HTML) 13 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Datenblatt Download

Link URL