AD813 datasheet(17/19 Pages) AD

17 / 19 page

AD813

REV. B

–17–

Disable Mode Operation

Pulling the voltage on any one of the Disable pins about 2.5 V

down from the positive supply will put the corresponding ampli-

fier into a disabled, powered down, state. In this condition, the

amplifier’s quiescent supply current drops to about 0.5 mA, its

output becomes a high impedance, and there is a high level of

isolation from input to output. In the case of the gain of two

line driver for example, the impedance at the output node will

be about the same as for a 1.4 k

Ω resistor (the feedback plus

gain resistors) in parallel with a 12.5 pF capacitor and the input

to output isolation will be about 65 dB at 1 MHz.

Leaving the Disable pin disconnected (floating) will leave the

corresponding amplifier operational, in the enabled state. The

input impedance of the disable pins is about 35 k

Ω in parallel

with a few pF. When grounded, about 50

µA flows out of a

disable pin on

±5 V supplies.

Input voltages greater than about 1.5 V peak-to-peak will defeat

the isolation. In addition, large signals (greater than 3 V peak-

to-peak) applied to the output node will cause the output im-

pedance to drop significantly.

When the Disable pins are driven by complementary output

CMOS logic (such as the 74HC04), the disable time is about

80 ns (until the output goes high impedance) and the enable

time is about 100 ns (to low impedance output) on

±15 V sup-

plies. When operated on

±15 V supplies, the disable pins

should be driven by open drain logic. In this case, pull-up resis-

tors from the disable pins to the plus supply will ensure mini-

mum switching time.

VOUT

CABLE

VIN1

+5V

464

590

SELECT1

VIN2

464

590

SELECT2

VIN3

464

590

SELECT3

–5V

Figure 55. A Fast Switching 3:1 Video Mux

(Supply Bypassing Not Shown)

Operation Using a Single Supply

The AD813 will operate with total supply voltages from 36 V

down to 2.4 V. With proper biasing (see Figure 52) it can

make an outstanding single supply video amplifier. Since the

input and output voltage ranges extend to within 1 V of the

supply rails, it will handle a 1.3 V peak-to-peak signal on a

single 3.3 V supply, or a 3 V peak-to-peak signal on a single

5 V supply. The small signal 0.1 dB bandwidths will exceed

10 MHz in either case, and the large signal bandwidths will

exceed 6 MHz.

The capacitively coupled cable driver in Figure 52 will achieve

outstanding differential gain and phase errors of 0.05% and 0.05

degrees respectively on a single 5 V supply. Resistor R2, in this

circuit, is selected to optimize the differential gain and phase by

biasing the amplifier in its most linear region.

AD813

VIN

12.4k

VOUT

+5V

CABLE

1 F

2 F

30 F

619

COUT

47 F

Figure 52. Biasing for Single Supply Operation

1000

100

FREQUENCY – MHz

–0.5

–3.0

0.5

–1.0

–1.5

–2.0

–2.5

–90

–180

–270

–3.5

GAIN

PHASE

VS = 5V

G = +2

RF = 619

RL = 150

Figure 53. Closed-Loop Gain and Phase vs. Frequency,

Circuit of Figure 52

100

500mV

50ns

VIN

VOUT

Figure 54. Pulse Response for the Circuit of Figure 52

with +VS = 5 V

AD813 Datenblatt(PDF) 17 Page - Analog Devices

AD813 Datenblatt(HTML) 17 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Datenblatt Download

Link URL