| Datenblatt-Suchmaschine für elektronische Bauteile |
|
MAX16948 Datenblatt(PDF) 4 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX16948 Datenblatt(HTML) 4 Page - Maxim Integrated Products |
|
4 / 15 page ![]() MAX16948 Automotive Dual Remote Antenna Current-Sense LDO/Switch 4 Maxim Integrated ELECTRICAL CHARACTERISTICS (continued) (VIN = 14V, TA = TJ = -40NC to +105NC, unless otherwise noted. Typical values are at TA = TJ = +25NC.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS FAILURE DETECTION LIM1 and LIM2 Current-Limit Threshold Voltage VLIM1/LIM2,TH Voltage on LIM1 and LIM2 for which output current is limited 2.375 2.5 2.625 V IN Overvoltage Lockout Threshold (Rising) VOVLO,R VIN rising 19 21 23 V IN Overvoltage Lockout Threshold (Falling) VOVLO,F VIN falling 18.5 V IN Overvoltage Lockout Hysteresis VOVLO,H 600 mV Short-to-BAT Threshold in Off State VS2B VOUT1/OUT2 - VIN, checked during turn- on sequence -500 -80 +110 mV Reverse Current Detection Level IREVCUR Power FET on (SW or LDO mode) -100 -50 -1 mA Reverse Current (Short-to-BAT) Shutdown Delay tPD-RC Delay to shutdown the switch or LDO after drop over RON becomes negative, IOUT1/OUT2 = -200mA (typ), TA = +25NC 4.16 20 F s Reverse Current Blanking Time tBLK-RC Blanking time for reverse current and FB1/FB2 out of range after rising edge of SHDN1, SHDN2, or current limiting event is over 16 ms Feedback Voltage Out of Range VFBERR LDO mode, internal pulldown resistor switched on, FB rising 1.12 1.15 1.28 V Feedback Voltage Out-of- Range Hysteresis VFBERR-HYS LDO mode, internal pulldown resistor switched on (Note 3) 39 100 mV OVERTEMPERATURE PROTECTION (Note 3) Thermal Shutdown TSHDN 160 N C Thermal Shutdown Hysteresis TSHDN-HYS 15 N C SUPPORTING CIRCUITS, INTERFACE SIGNALS Internal Voltage Regulator VREG TA = +25NC, IREG = 0mA, VIN = 4.5V to 18V 4 5 5.5 V TA = +25NC, IREG = 0mA, VIN = 6.5V to 18V 4.5 5 5.5 V Internal Voltage Regulator Current Limit IREG (Note 4) 15 mA ERR1 and ERR2 Output- Voltage Low VOL Sinking current = 10mA 0.4 V ERR1 and ERR2 Open-Drain Leakage Current ERR1 and ERR2 not asserted, VERR1/ ERR2 = 5V, TA = +25NC 1 F A SHDN1 and SHDN2 High VSHDN1/SHDN2,HI 2.8 V SHDN1 and SHDN2 Low VSHDN1/SHDN2,LO 0.8 V |
|
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |