IO130PDB3V2 datasheet(91/212 Pages) MICROSEMI

91 / 212 page

Military ProASIC3/EL Low Power Flash FPGAs

Revision 3

2-77

2.5 V GTL

Gunning Transceiver Logic is a high-speed bus standard (JESD8-3). It provides a differential amplifier

input buffer and an open-drain output buffer. The VCCI pin should be connected to 2.5 V.

Timing Characteristics

Table 2-123 • Minimum and Maximum DC Input and Output Levels

2.5 V GTL

VIL

VIH

VOL

VOH

IOL IOH

IOSL

IOSH

IIL1 IIH2

Drive

Strength

Min.

Max.

Min.

Max.

Min.

VmA mA

Max.

mA3

Max.

mA3

µA4 µA4

20 mA5

–0.3

VREF – 0.05 VREF + 0.05

3.6

0.4

–

20 20

169

124

15 15

Notes:

1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 V < VIN < VIL.

2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is

larger when operating outside recommended ranges.

3. Currents are measured at 100°C junction temperature and maximum voltage.

4. Currents are measured at 125°C junction temperature.

5. Output drive strength is below JEDEC specification.

Figure 2-17 • AC Loading

Table 2-124 • AC Waveforms, Measuring Points, and Capacitive Loads

Input Low (V)

Input High (V)

Measuring

Point* (V)

VREF (typ.) (V)

VTT (typ.) (V)

CLOAD (pF)

VREF – 0.05

VREF + 0.05

0.8

1.2

Note:

*Measuring point = Vtrip. See Table 2-28 on page 2-27 for a complete table of trip points.

Test Point

10 pF

GTL

VTT

Table 2-125 • 2.5 V GTL

Military-Case Conditions: TJ = 125°C, Worst-Case VCC = 1.14 V,

Worst-Case VCCI = 3.0 V, VREF = 0.8 V

Applicable to Pro I/Os for A3PE600L and A3PE3000L Only

Speed

Grade

tDOUT

tDP

tDIN

tPY

tEOUT

tZL

tZH

tLZ

tHZ

tZLS

tZHS

Units

Std.

0.80

2.11

0.05

2.26

0.52

2.14

2.11

–

4.34

4.31

–1

0.68

1.79

0.05

1.93

0.44

1.82

1.79

–

3.70

3.68

Note:

For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.

Table 2-126 • 2.5 V GTL

Military-Case Conditions: TJ = 125°C, VCC = 1.425 V,

Worst-Case VCCI = 3.0 V, VREF = 0.8 V

Applicable to Pro I/Os for A3PE600L and A3PE3000L Only

Speed

Grade

tDOUT

tDP

tDIN

tPY

tEOUT

tZL

tZH

tLZ

tHZ

tZLS

tZHS

Units

Std.

0.61

2.02

0.04

2.04

0.40

1.98

2.02

–

3.45

3.49

–1

0.52

1.72

0.03

1.73

0.34

1.69

1.72

–

2.93

2.97

Note:

For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.

IO130PDB3V2 Datenblatt(PDF) 91 Page - Microsemi Corporation

IO130PDB3V2 Datenblatt(HTML) 91 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL