PIC24F16KA102T-E datasheet(66/278 Pages) MICROCHIP

66 / 278 page

PIC24F16KA102 FAMILY

DS39927C-page 66

 2008-2011 Microchip Technology Inc.

8.3

Interrupt Control and Status

Registers

The PIC24F16KA102 family of devices implements a

total of 22 registers for the interrupt controller:

• INTCON1

• INTCON2

• IFS0, IFS1, IFS3 and IFS4

• IEC0, IEC1, IEC3 and IEC4

• IPC0 through IPC5, IPC7 and IPC15 through

IPC19

•INTTREG

Global interrupt control functions are controlled from

INTCON1 and INTCON2. INTCON1 contains the

Interrupt Nesting Disable (NSTDIS) bit, as well as the

control and status flags for the processor trap sources.

The INTCON2 register controls the external interrupt

request signal behavior and the use of the AIV table.

The IFSx registers maintain all of the interrupt request

flags. Each source of interrupt has a status bit, which is

set by the respective peripherals, or external signal,

and is cleared via software.

The IECx registers maintain all of the interrupt enable

bits. These control bits are used to individually enable

interrupts from the peripherals or external signals.

The IPCx registers are used to set the interrupt priority

level for each source of interrupt. Each user interrupt

source can be assigned to one of eight priority levels.

The INTTREG register contains the associated inter-

rupt vector number and the new CPU interrupt priority

level, which are latched into the Vector Number

(VECNUM<6:0>) and the Interrupt Level (ILR<3:0>) bit

fields in the INTTREG register. The new interrupt

priority level is the priority of the pending interrupt.

The interrupt sources are assigned to the IFSx, IECx

and IPCx registers in the same sequence listed in

Table 8-2. For example, the INT0 (External Interrupt 0)

is depicted as having a vector number and a natural

order priority of 0. Thus, the INT0IF status bit is found

in IFS0<0>, the INT0IE enable bit in IEC0<0> and the

INT0IP<2:0> priority bits in the first position of IPC0

(IPC0<2:0>).

Although they are not specifically part of the interrupt

control hardware, two of the CPU control registers

contain bits that control interrupt functionality. The ALU

STATUS register (SR) contains the IPL<2:0> bits

(SR<7:5>). These indicate the current CPU interrupt

priority level. The user may change the current CPU

priority level by writing to the IPL bits.

The CORCON register contains the IPL3 bit, which

together with IPL<2:0>, also indicates the current CPU

priority level. IPL3 is a read-only bit so that the trap

events cannot be masked by the user’s software.

All interrupt registers are described in Register 8-1

through Register 8-21, in the following sections.

PIC24F16KA102T-E Datenblatt(PDF) 66 Page - Microchip Technology

PIC24F16KA102T-E Datenblatt(HTML) 66 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL