PIC24F16KA102T-E datasheet(126/278 Pages) MICROCHIP

126 / 278 page

PIC24F16KA102 FAMILY

DS39927C-page 126

 2008-2011 Microchip Technology Inc.

15.3

Pulse-Width Modulation (PWM)

Mode

The following steps should be taken when configuring

the output compare module for PWM operation:

Set the PWM period by writing to the selected

Timer Period register (PRy).

Set the PWM duty cycle by writing to the OC1RS

Write the OC1R register with the initial duty

cycle.

Enable interrupts, if required, for the timer and

output compare modules. The output compare

interrupt is required for PWM Fault pin

utilization.

Configure the output compare module for one of

two PWM Operation modes by writing to the

Output

Compare

Mode

bits,

OCM<2:0>

(OC1CON<2:0>).

Set the TMRy prescale value and enable the

time base by setting TON (TxCON<15>) = 1.

15.3.1

PWM PERIOD

The PWM period is specified by writing to PRy, the

Timer Period register. The PWM period can be

calculated using Equation 15-1.

EQUATION 15-1:

CALCULATING THE PWM

PERIOD(1)

15.3.2

PWM DUTY CYCLE

The PWM duty cycle is specified by writing to the

OC1RS register. The OC1RS register can be written to

at any time, but the duty cycle value is not latched into

OC1R until a match between PRy and TMRy occurs

(i.e., the period is complete). This provides a double

buffer for the PWM duty cycle and is essential for

glitchless PWM operation. In PWM mode, OC1R is a

read-only register.

Some important boundary parameters of the PWM duty

cycle include:

• If the Output Compare 1 register, OC1R, is loaded

with 0000h, the OC1 pin will remain low (0% duty

cycle).

• If OC1R is greater than PRy (Timer Period

cycle).

• If OC1R is equal to PRy, the OC1 pin will be low

for one time base count value and high for all

other count values.

See Example 15-1 for PWM mode timing details.

Table 15-1 provides an example of PWM frequencies

and resolutions for a device operating at 10 MIPS.

EQUATION 15-2:

CALCULATION FOR MAXIMUM PWM RESOLUTION(1)

Note:

The OC1R register should be initialized

before the output compare module is first

enabled. The OC1R register becomes a

read-only Duty Cycle register when the

module is operated in the PWM modes.

The value held in OC1R will become the

PWM duty cycle for the first PWM period.

The contents of the Output Compare 1

Secondary register, OC1RS, will not be

transferred into OC1R until a time base

period match occurs.

Note:

A PRy value of N will produce a PWM

period of N + 1 time base count cycles. For

example, a value of 7, written into the PRy

8 time base cycles.

PWM Period = [(PRy) + 1] • TCY • (Timer Prescale Value)

PWM Frequency = 1/[PWM Period]

where:

Note 1:

Based on TCY = 2 * TOSC; Doze mode

and PLL are disabled.

(

)

Maximum PWM Resolution (bits) =

FCY

FPWM • (Timer Prescale Value)

log10

log10(2)

bits

Note 1:

Based on FCY = FOSC/2; Doze mode and PLL are disabled.

PIC24F16KA102T-E Datenblatt(PDF) 126 Page - Microchip Technology

PIC24F16KA102T-E Datenblatt(HTML) 126 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL