| Datenblatt-Suchmaschine für elektronische Bauteile |
|
ADF7021 Datenblatt(PDF) 49 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADF7021 Datenblatt(HTML) 49 Page - Analog Devices |
|
49 / 64 page ![]() Data Sheet ADF7021 Rev. B | Page 49 of 64 REGISTER 2—TRANSMIT MODULATION REGISTER P6 0 0 0 0 . . 1 . . . . . . . . . . . . . . . 1 P2 0 0 1 1 . . 1 P1 0 1 0 1 . . 1 0 (PA OFF) 1 (–16.0 dBm) 2 3 . . 63 (13 dBm) TFD9 0 0 0 0 . 1 TFD3 0 0 0 0 . 1 ... ... ... ... ... ... ... TFD2 0 0 1 1 . 1 TFD1 0 1 0 1 . 1 0 1 2 3 . 511 Tx_FREQUENCY_DEVIATION POWER_AMPLIFIER TxDATA_ INVERT PA_BIAS PA_RAMP MODULATION_ SCHEME ADDRESS BITS PE1 0 1 POWER AMPLIFIER OFF ON PA2 0 0 1 1 PA1 0 1 0 1 PA BIAS 5µA 7µA 9µA 11µA DI2 0 0 1 1 DI1 0 1 0 1 TxDATA INVERT NORMAL INVERT CLK INVERT DATA INV CLK AND DATA S3 0 0 0 0 1 1 1 1 S2 0 0 1 1 0 0 1 1 MODULATION SCHEME 2FSK GAUSSIAN 2FSK 3FSK 4FSK OVERSAMPLED 2FSK RAISED COSINE 2FSK RAISED COSINE 3FSK RAISED COSINE 4FSK S1 0 1 0 1 0 1 0 1 PR3 0 0 0 0 1 1 1 1 PR2 0 0 1 1 0 0 1 1 PA RAMP RATE NO RAMP 256 CODES/BIT 128 CODES/BIT 64 CODES/BIT 32 CODES/BIT 16 CODES/BIT 8 CODES/BIT 4 CODES/BIT PR1 0 1 0 1 0 1 0 1 NRC1 0 1 RAISED COSINE ALPHA 0.7 0.5 (Default) fDEV PA LEVEL Figure 64. Register 2—Transmit Modulation Register Map The 2FSK/3FSK/4FSK frequency deviation is expressed by the following: Direct output Frequency Deviation [Hz] = 16 2 PFD ON CY_DEVIATI Tx_FREQUEN × With RF_DIVIDE_BY_2 (R1_DB18) enabled Frequency Deviation [Hz] = 16 2 5 . 0 PFD ON CY_DEVIATI Tx_FREQUEN × × where Tx_FREQUENCY_DEVIATION is set by DB[19:27] and PFD is the PFD frequency. In the case of 4FSK, there are tones at ±3 × the frequency deviation and at ±1 × the deviation. The power amplifier (PA) ramps at the programmed rate (R2_DB[8:10]) until it reaches its programmed level DB[13:18]. If the PA is enabled/disabled by the PA_ENABLE bit (DB7), it ramps up and down. If it is enabled/disabled by the Tx/Rx bit (R0_DB27), it ramps up and turns hard off. R-COSINE_ALPHA sets the roll-off factor (alpha) of the raised cosine data filter to either 0.5 or 0.7. The alpha is set to 0.5 by default, but the raised cosine filter bandwidth can be increased to provide less aggressive data filtering by using an alpha of 0.7. |
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |