Dynatem Inc., (800)543-3830, (949)855-3235, Fax: (949)770-3481, Email:sales@dynatem.com, Web:www.dynatem.com

DRAM

2 or 4 GBytes of DDR2-400 memory

Two banks that are each 64 bits wide with ECC support

CompactPCI

PICMG 2.0 R3.0 Compliant

PLX non-transparent PCI-PCI bridge provides 64-bit

CompactPCI transfer rates at 66 MHz

Universal bridge lets the CPD2 operate as a system

controller or a peripheral slot module

Supports Hot Swapping according to PICMG 2.1 R2.0

Connectors J3 and J5 are used for I/O expansion

PMC Expansion

Two PMC sites each with a dedicated 64-bit 133 MHz

PCI-X bus interfaced to the E7520 via two separate

Tsi384 PCIe to PCI-X bridges. This architecture

provides 1 GB access to E7520

One of PMC sites supports XMC modules with x8 PCIe

Ethernet/PICMG 2.16

Two Intel 82571EB dual PCI express Ethernet controllers

provide a total of four 10/100/1000BaseTX ports

Two ports routed to the front panel

Two ports routed to the J3 connector in compliance with

PICMG 2.16 for backplane fabric switching or for

alternate routing to an optional rear I/O card

Graphics

The Silicon Motion SM712 ultra low-power display

controller with 4 MB on-chip memory

VGA routed to J5

IDE/Flash

Primary ATA/100 DMA IDE interface is optionally

accessible from the J5

Secondary IDE port is routed to a Silicon Motion SM-

2231

NAND Flash controller.

16 GB of NAND Flash is installed

BIOS

Phoenix’s flash-based system BIOS with boot options

including CD-ROM, USB, and PXE over Ethernet

Watchdog

Programmable watchdog timer for system recovery

I/O interfaces accessible from the front panel

Dual 10/100/1000BaseTX, Dual USB 2.0, access to both

PMC sites

2

I/O interfaces routed to optional rear plug-in board

VGA, IDE, COM1/2/3/4 (COM2 optionally RS-422), dual

Serial ATA, keyboard, mouse, and dual USB 2.0 ports

(routed through J5)

Two Gb Ethernet ports in compliance with PICMG 2.16

(routed through J3)

Access to both PMC sites

XPDRIO Rear Transition Module

Optional rear I/O interface board (RTM) with:

One USB connector

40-pin IDE connector

Two RJ-45 connectors for Gb Ethernet

One SATA connector

COM 1,2,3,4 connector (COM3 has RS-422 option)

PS/2 keyboard mouse

VGA

Audio In and Out

Two optional PMC Interface (PIM) Modules

XPDRIO2 Rear Transition Module

Optional rear I/O interface board (RTM) with:

Two USB connectors

Optional 40-pin IDE connector

Two RJ-45 connectors for Gb Ethernet

One SATA connector on front panel plus a 1.8" SATA

drive connector for mounting onboard

COM 1,2 optional COM3, 4 (COM3 has RS-422

option)

PS/2 keyboard mouse option

VGA

Two optional PMC Interface (PIM) Modules

Operating temperature

The CPD2 has a standard operating temperature range of

0°/+70° C

Extended temp versions are available

Rugged/Conduction-cooled Versions

CRD2 is a conduction-cooled version of the CPD2

Convection-cooled and conduction-cooled versions have

conformal coating as an option

Net Weight

Approximately 15 oz

Power Requirements

1.5 GHz L7400: +5VDC @5.5A peak,

3.3VDC@2.0A steady

3.0VDC Lithium Coin Cell @3.4 µA

2.16 GHz T7400: +5VDC @8.0A peak