MAX2601ESA datasheet(2/6 Pages) MAXIM

2 / 6 page

dBc

3.6V, 1W RF Power Transistors

for 900MHz Applications

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

DC ELECTRICAL CHARACTERISTICS

(TA = TMIN to TMAX, unless otherwise noted.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Collector-Emitter Voltage, Shorted Base (VCES) ....................17V

Emitter Base Reverse Voltage (VEBO)...................................2.3V

BIAS Diode Reverse Breakdown Voltage (MAX2602) ..........2.3V

Average Collector Current (IC)........................................1200mA

Continuous Power Dissipation (TA = +70°C)

PSOPII (derate 80mW/°C above +70°C) (Note 1) ..........6.4W

Operating Temperature Range ...........................-40°C to +85°C

Storage Temperature Range .............................-65°C to +165°C

Junction Temperature ......................................................+150°C

Lead Temperature (soldering, 10sec) .............................+300°C

IC < 100µA

5.0

LVCEO

Collector-Emitter Sustaining

Voltage

BVCES

BVCEO

Collector-Emitter Breakdown

Voltage

100

hFE

DC Current Gain

µA

0.05

1.5

ICES

Collector Cutoff Current

9.6

COB

Output Capacitance

UNITS

MIN

TYP

MAX

SYMBOL

PARAMETER

Note 1: Backside slug must be properly soldered to ground plane (see

Slug Layout Techniques section).

IC = 200mA

Shorted base

Open base

IC = 250mA, VCE = 3V

VCE = 6V, VBE = 0V

VCB = 3V, IE = 0mA, f = 1MHz

CONDITIONS

3.3

Noise Figure

dBc

-25

IM5

Two-Tone IMR

-16

IM3

8:1

VSWR

Stability under Continuous

Load Mismatch Conditions

Collector Efficiency

11.6

Power Gain

-42

2fo, 3fo

Harmonics

-43

4.2

Base Current

GHz

Frequency Range

UNITS

MIN

TYP

MAX

SYMBOL

PARAMETER

VBB = 0.9V

POUT = +30dBm total power, f1 = 835MHz,

f2 = 836MHz

VCC = 3.6V, POUT = 30dBm

VCC = 5.5V, all angles (Note 3)

(Note 2)

No modulation

POUT = 30dBm

CONDITIONS

AC ELECTRICAL CHARACTERISTICS

(Test Circuit of Figure 1, VCC = 3.6V, VBB = 0.750V, ZLOAD = ZSOURCE = 50Ω, POUT = 30dBm, f = 836MHz, TA = +25°C, unless oth-

erwise noted.)

Note 2: Guaranteed by design.

Note 3: Under these conditions: a) no spurious oscillations shall be observed at collector greater than -60dBc; b) no parametric

degradation is observable when mismatch is removed; and c) no current draw in excess of the package dissipation

capability is observed.

BVCBO

Collector-Base Breakdown

Voltage

IC < 100µA, emitter open

VCC = 3.0V, POUT = 29dBm

dBc

MAX2601ESA Datenblatt(PDF) 2 Page - Maxim Integrated Products

MAX2601ESA Datenblatt(HTML) 2 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6

Datenblatt Download

Link URL