PRODUCT SPECIFICATIONS:

300W ~ 400W AC-DC ACTIVE PFC SWITCHING POWER SUPPLY

PRL1201D DUAL OUTPUT SERIES

Input Voltage: 90 ~ 264Vac full range, 47 ~ 63Hz.

Input Current: 6A at 90VAC full load.

Inrush Current: 70A peak maximum.(Measuring at 230VAC and full

load cold start.)

Power Factor Correction: Pass EN61000-3-2 class D

Transient Response: Returns to within 1% in less than 2.5mS for a

50% load change and the peak transient does not excess 5%.

Overshoot: Turn-on & turn-off not exceed 5% over nominal voltage.

Efficiency: 80% minimum (Measuring at 115V and full load)

Turn On Delay: 2 second maximum at 115 VAC.

Hold Up Time: 16 m sec. minimum at 115VAC and 75% of rated

maximum load.

Adjustability: Output user adjustable +/-5% minimum.

Remote On-Off: Designated as RSW on the CN3, requires a low

signal to inhibit output.

Power Supply On: When the Bi-color LED emit green light that

indicates the supply is operating. When any protection is occurred or

RSW is applied a low signal, the Bi-color LED will emit orange light.

Power Good: Designated as PG on CN3. This signal will go high

100-500 Msec after the output reaches the regulation limit. It goes

low at least 1 Msec before loss of regulation and has ability to sink

100mA.

Input Circuit Protection (primary): One T6.3A/250V fuse inserted.

Input Voltage Protection: Power shut down under 80 +/-10Vac, and

recovered over 90 Vac.

Over-Power Protection: 110~140% of the rated output current and

Over-Voltage Protection: Latching down will occur when output

voltage exceed 130% max., and recycle AC input to reset.

Over Temp. Protection: Protected at ambient 110 +/- 5 ℃; Auto-

recovery.

Short Circuit Protection: Trip without damage and auto-recovery.

Operating Temperature: 0℃ to +50℃

Switching Frequency: PFC 60K Hz; PWM 27K Hz.

Storage Temperature: -20 to +85 degrees C.

Operating Humidity: 5% to 90% RH, Non-condensing.

Storage Humidity: 5% to 95% RH, Non-condensing.

Vibration: Frequency 5 to 50 Hz, acceleration +/-7.35 M/(SxS) on

X,Y and Z Axis.

EMC: EN55022 class B conducted / radiated, EN61000-3-2,

EN61000-3-3; EN55024 (IEC61000-4-2, IEC61000-4-3, IEC61000-4-

4, IEC61000-4-5, IEC61000-4-6, IEC61000-4-11).

Safety: Approved UL60950-1, CSA C22.2 No. 950-95, EN60950 and

CB certificate available

Leakage Current: < 500uA at 240Vac

HI-POT Test: 1500 VAC between input line and chassis (10mA AC

cut off current); 3000VAC between primary and secondary windings;

Primary to core 1500VAC. All for 3 sec.

Grounding Test: Apply 25 A from ground pin to the earthed

connection point. Maximum allowable resistance is 0.1ohm.

Warranty: 2 years.

MTBF: 100000 Hrs (according to MIL-HBK-217F) at 30℃.

Burn in: 45 +/- 5 degree C for 1 hour @230Vac with full load.

Weight: 1KG

Copy Right Ultra Level Tech Co., Ltd 2015, All Right Reserved. Specifications subject to change without notice.

ULTRA LEVEL TECH CO., LTD.

www.ultralevel.com.tw

Tel:+886-2-29180118

Fax:+886-2-29181465

U Type (U-Chassis only):

5(W) x 8(L )x 1.6(H) inches.

FEATURES:

◆ 400W convection cooling with 1U height

◆ Design meets IEC/EN/UL60950-1 Latest Edition

◆ Power Factor Corrected to EN61000-3-2 class D

◆ High Quality & Reliable Component Usage

◆ 5/ 12/ 24V Dual Output Optional Combinations

◆ Full Range AC Input