480W Single Output with PFC Function

WWW.ASTRODYNETDI.COM

ASTRODYNE USA: 1-800-823-8082

ASTRODYNE PACIFIC: 886-2-26983458

INPUT SPECIFICATIONS

Input Voltage Range (Note 5)

90 ~ 264VAC 120~370 Volts(DC)

Frequency Range

47-63 Hz

Inrush Current, typ: (cold start)

20Amps/115VAC; 40Amps 230VAC

Input Current

6.5Amps @ 115VAC

3.5 Amps @ 230VAC

Leakage current

< 2mAmps / 240VAC

Min Load

See Selection Chart

Power Factor @ FL

PF > 0.95 / 230VAC

> 0.98 / 115VAC

OUTPUT SPECIFICATIONS

Voltage and Current (Note3) See Selection Chart

Line Regulation

±0.5%: 3.3;5Volts(DC)

±0.3%: 12;15Volts(DC)

±0.2%: 24;48Volts(DC)

Load Regulation

±1.0%: 3;5Volts(DC)

±0.5%: 12~48Volts(DC)

Voltage Tolerance (Note 2)

±2.0%: 3.3;5Volts(DC)

±1.5%: 12;15Volts(DC)

±1.0%: 24;48Volts(DC)

Ripple/Noise (Note 1)

80mVpk-pk: 3.3;5Volts(DC)

120mVpk-pk: 12Volts(DC)

150mVpk-pk: 15;24Volts(DC)

240mVpk-pk: 48Volts(DC)

Hold Up Time @ FL

18mS /230VAC

18mS /115VAC

Setup, Rise Time @ FL

1000mS, 80mS /230VAC

2500mS, 80mS /115VAC

Over Voltage Protection

See Selection Chart

Shut down o/p volt,re power

Over Current Protection

See Selection Chart

Constant current limiting,auto recover

Over Temperature (Note 3)

80°C TSW1: detect on heatsink of power transistor

90°C TSW2: detect on heatsink of power diode

Shut down o/p voltage, auto recover

DC Volt Adjust

See Selection Chart

Peak Load: 10min (Note 4 )

10% max

GENERAL SPECIFICATIONS

Safety

UL60950-1,

TUV EN60950-1 Approved

Insulation Resistance

≥ 100MΩ / 500Volts(DC)

EMI

Compliance to EN55022B (CISPR22B)

Harmonic Current

Compliance to EN61000-3-2,-3

Remote Control

RC+/RC-: 4~10Volts(DC) Power off

0 ~ 0.8Volts(DC) Power on

Efficiency

See Selection Chart

Isolation

3000VAC Input - Output

1500VAC Input - Ground

Short Output - Ground

EMS

Compliance to

EN61000-4-2,3,4,5,6,8,11

ENV50204,EN61000-6-2(EN50082-2)

light Industry Level, Criteria A

ENVIRONMENTAL SPECIFICATIONS

Oper. Temperature

-20°C to +60°C (See Derate Curve)

Storage Temperature

-40°C to +85°C, 10~95% RH

Relative Humidity

20~90% RH non cond

Temperature Coefficient

±0.03% / °C (0-50°C)

MTBF

120.5KHrs min,MIL-HDBK-217F(25°C)

Vibration

10~500Hz, 2G10min./1cycle, period for

60min. each along X, Y, Z axes

PHYSICAL SPECIFICATIONS

Size

278x127 x 43mm (10.94”x5 ”x1.69”)

Weight

59.97 oz (1700g)

NOTE

1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”

twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

2. Tolerance : includes set up tolerance, line regulation and load regula-

tion.

3. TSW1: Detect on heatsink of power transistor.

TSW2: Detect on heatsink of output diode.

4. 33% Duty cycle maximum within every 30 minute. Average output

power should not exceed the rated POWER.

5. Derating may be needed under low input voltages. Please check the

derating curve for more details.

All specifications are typical at nominal input, full load, and 25°C unless other-

wise noted