DM6382F datasheet(12/40 Pages) ETC

12 / 40 page

DM336P

V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set

Final

Version: DM336P-DS-F02

August 15, 2000

f. Modem Control Register (MCR): Address 4

Reset State 00h

bit7

bit6

bit5

bit4

bit3

bit2

bit1

bit0

000000

RTS DTR

Bit 0: This bit asserts a Data Terminal Ready

condition that is readable via port P1.1 of micro-

controller 8031. When bit 0 is set to logic 1, the

P1.1 is forced to logic 0. When bit 0 is reset to

logic 0, the P1.1 is forced to logic 1.

Bit 1: This bit asserts a Request To Send condition

that is readable via port P3.4 of the micro-

controller 8031. Bit 1 affects P3.4 in a manner

identical to that described above for bit 0.

g. Line Status Register (LSR): Address 5

Reset State 60h, Read only

bit7

bit6

bit5

bit4 bit3 bit2 bit1 bit0

RCV ETEMT THRE

This register provides status information to the host

PC concerning the data transfer. Bit 1-4 indicate the

error conditions that produce a Receiver Line Status

interrupt whenever any of the corresponding

conditions are detected. The Line Status Register is

intended for read operations only.

Bit 0: Set to logic 1 when a received character is

available in the RxFIFO. This bit is reset to logic

0 when the RxFIFO is empty.

Bit 1: An Overrun error will occur only after the

RxFIFO is full and the next character has

overwritten the unread FIFO data. This bit is

reset upon reading the Line Status Register.

Bit 2: A value of logic 1 indicates that a received

character does not have the correct even or

odd parity as selected by the Even Parity Select

bit. This error is set when the corresponding

character is at the top of the RxFIFO. It will

remain set until the CPU reads the LSR. This

Parity Error indication is associated with the

particular character in the FIFO to which it

applies. This error is revealed to the CPU when

its associated character is at the top of the

FIFO.

Bit 3: This bit is the Framing Error (FE) indicator. Bit 3

indicates that the received character did not

have a valid stop bit. Bit 3 is set to a logic 1

whenever the stop bit following the last data bit

or parity bit is detected as a zero bit (spacing

level). The FE bit is reset whenever the CPU

reads the contents of the Line Status Register.

The FE error condition is associated with the

particular character in the FIFO to which it

applies. This error is revealed to the CPU when

its associated character is at the top of the

FIFO.h. Modem Status Register (MSR):

Address 6 Reset State, bit 0-3: low, bit 4-7:

input signal.

Bit 4: This bit is a Break Interrupt (BI) indicator. Bit 4

is set to logic 1 whenever the received data

input is held in the Spacing (logic 0) state for

longer than a full word transmission time (that is,

the total time of Start bit + data bits + Parity +

Stop bits). The BI indicator is reset whenever

the CPU reads the contents of the Line Status

with the particular character in the FIFO to

which it applies. This error is revealed to the

CPU when its associated character is at the top

of the FIFO.

Bit 5: This bit is a Transmitter Holding Register Empty

indicator. Bit 5 indicates that UART is ready to

accept a new character for transmission. In

addition, this bit causes UART to issue an

interrupt to the CPU when the Transmit Holding

THRE bit is reset to logic 0 when the host CPU

loads a character into the Transmit Holding

the TxFIFO is empty, and is cleared when at

least 1 byte is written to the TxFIFO.

Bit 6: This bit is the Transmitter Empty indicator. Bit 6

is set to a logic 1 whenever the Transmitter

Holding Register (THR) is empty, and is reset to

a logic 0 whenever the THR contains a

character. In FIFO mode, this bit is set to 1

whenever the transmitter FIFO is empty.

Bit 7: In character mode, this bit is 0. In FIFO mode,

this bit is set when there is at least one parity

error, framing error, or break indication in the

FIFO. If there are no subsequent errors in the

FIFO, LSR7 is cleared when the CPU reads the

LSR.

DM6382F Datenblatt(PDF) 12 Page - List of Unclassifed Manufacturers

DM6382F Datenblatt(HTML) 12 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Datenblatt Download

Link URL