| Datenblatt-Suchmaschine für elektronische Bauteile |
|
LP3936 Datenblatt(PDF) 13 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
LP3936 Datenblatt(HTML) 13 Page - National Semiconductor (TI) |
|
13 / 20 page ![]() Boost Output Voltage Control User can control the boost output voltage by boost output 8-bit register. Boost[7:0] Register 0Dh BOOST Output Voltage (typical) Binary Hex 0000 0000 00 4.10 0000 0001 01 4.25 0000 0011 03 4.40 0000 0111 07 4.55 Default 0000 1111 0F 4.70 0001 1111 1F 4.85 0011 1111 3F 5.00 0111 1111 7F 5.15 1111 1111 FF 5.30 Boost Output Voltage Control 20081418 Magnetic Boost DC/DC Converter Electrical Characteristics Symbol Parameter Conditions Min Typ Max Units I LOAD Load Current 3.0V ≤ V IN ≤ 4.5V V OUT = 4.55V 0 250 mA V OUT Output Voltage Accuracy (FB Pin) 1 mA ≤ I LOAD ≤ 225 mA 3.0V ≤ V IN ≤ V (FB)−0.5V V OUT = 4.55V −5 +5 % Output Voltage (FB Pin) 1 mA ≤ I LOAD ≤ 250 mA 3.0V < V IN < 4.55V + V (SCHOTTKY) 4.55 V 1mA ≤ I LOAD ≤ 250 mA V IN > 4.55V + V(SCHOTTKY) V IN–V(SCHOTTKY) V RDS ON Switch ON Resistance V DD1,2 = 3.6V, ISW = 0.5A 0.4 0.5 Ω f PWF PWM Mode Switching Frequency RT = 82 k Ω 1 MHz Frequency Accuracy RT = 82 k Ω −6 ±3+6 % −10 +10 t STARTUP Startup Time 25 ms I CL_OUT OUT Pin Current Limit V DD = 3.6V 600 750 1050 mA 400 1200 PFM/PWM Mode User can change the Boost converters mode between PWM (Pulse Width Modulation) and PFM (Pulse Frequency Modulation). The startup is done on PFM mode and then the device runs on PWM mode (as a default). User can set PFM mode by turning “pfm_mode” register bit HIGH. PFM is recommended to use with light loads and PWM with high loads. Boost Standby Mode User can set boost converter to STANDBY mode by writing register bit EN_BOOST low. This mode can be useful when driving LEDs directly from battery voltage. This may be possible if LED forward voltage is low, battery voltage is high and LED current is low. When EN_BOOST is written high, the converter starts for 10 ms in PFM mode and then goes to PWM mode if PWM mode has been selected (default). Unused Boost Converter If the boost converter is not used, it should be disabled by writing bit en_boost low. OUT pin should be connected to GND and FB pin to the LED supply voltage. www.national.com 13 |
|
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |