 |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
|
Datenblatt-Suchmaschine für elektronische Bauteile |
|
HCPL-0721 Datenblatt(PDF) 8 Page - Agilent(Hewlett-Packard) |
|
|
|||||||||||||||||||||||||||||
HCPL-0721 Datenblatt(HTML) 8 Page - Agilent(Hewlett-Packard) |
|
|
8 / 18 page  8 Notes: 1. Absolute Maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not guarantee functionality. 2. The LED is ON when VI is low and OFF when VI is high. 3. tPHL propagation delay is measured from the 50% level on the falling edge of the VI signal to the 50% level of the falling edge of the VO signal. tPLH propagation delay is measured from the 50% level on the rising edge of the VI signal to the 50% level of the rising edge of the VO signal. 4. PWD is defined as |tPHL - tPLH|. %PWD (percent pulse width distortion) is equal to the PWD divided by pulse width. 5. tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the recommended operating conditions. 6. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common mode voltage slew rate that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. 7. Unloaded dynamic power dissipation is calculated as follows: CPD * VDD2 * f + IDD * VDD, where f is switching frequency in MHz. 8. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together. 9. In accordance with UL1577, each HCPL-072X is proof tested by applying an insulation test voltage ≥4500 V RMS for 1 second (leakage detection current limit, II-O ≤5 µA). Each HCPL-772X is proof tested by applying an insulation test voltage ≥4500 Vrms for 1 second (leakage detection current limit. II-O ≤ 5 µA.) 10. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.” 11. CI is the capacitance measured at pin 2 (VI). Figure 1. Typical output voltage vs. input voltage. Figure 2. Typical input voltage switching threshold vs. input supply voltage. Figure 3. Typical propagation delays vs. temperature. 0 0 VI (V) 5 4 1 4 12 3 5 3 2 0 °C 25 °C 85 °C 4.5 1.6 VDD1 (V) 5.5 2.1 1.7 5.25 4.75 5 2.2 2.0 1.8 1.9 0 °C 25 °C 85 °C 0 15 TA (C) 80 27 17 60 20 30 29 25 19 21 10 40 50 70 23 TPLH TPHL Package Characteristics Parameter Symbol Min. Typ. Max. Units Test Conditions Fig. Note Input-Output Momentary 072X VISO 3750 Vrms RH ≤50%, 8, 9, Withstand Voltage 772X 3750 t = 1 min., 10 TA = 25°C Resistance RI-O 1012 Ω VI-O = 500 Vdc 8 (Input-Output) Capacitance CI-O 0.6 pF f = 1 MHz (Input-Output) Input Capacitance CI 3.0 11 Input IC Junction-to-Case -772X θ jci 145 °C/W Thermocouple Thermal Resistance -072X 160 located at center Output IC Junction-to-Case -772X θ jco 140 underside of package Thermal Resistance -072X 135 Package Power Dissipation PPD 150 mW |
|
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
German ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
