LM74 datasheet(6/15 Pages) NSC

6 / 15 page

Logic Electrical Characteristics (Continued)

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating

the device beyond its rated operating conditions.

Note 2: When the input voltage (VI) at any pin exceeds the power supplies (VI < GND or VI > +VS) the current at that pin should be limited to 5 mA. The 20 mA

maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to four.

Note 3: See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in a current National

Semiconductor Linear Data Book for other methods of soldering surface mount devices.

Note 4: Human body model, 100 pF discharged through a 1.5 k

Ω resistor. Machine model, 200 pF discharged directly into each pin.

Note 5: The life expectancy of the LM74 will be reduced when operating at elevated temperatures. LM74

θJA (thermal resistance, junction-to-ambient) when

attached to a printed circuit board with 2 oz. foil is summarized in the table below:

Device Number

NS Package

Number

Thermal

Resistance (

JA)

LM74CIM

M08A

160˚C/W

LM74CIBP

BPD05MPB

250˚C/W

Note 6: All SOP (LM74CIM) parts will function over the V+ supply voltage range of 3V to 5.5V. All micro SMD (LM74SIBP) parts will function over the V+ supply

voltage range of 2.65V to 5.5V. The SOP (LM74CIM) parts are tested and specified for rated temperature error at their nominal supply voltage for temperature ranges

of −10˚C to +65˚C, −55˚C to +125˚C and −55˚C to +150˚C. For the SOP (LM74CIM) parts the temperature error specifications for temperature ranges of −40˚Cto

+85˚C, −25˚C to +110˚C and −40˚C to +110˚C include error induced by power supply variation of ±5% from the nominal value. For the LM74CIM (SOP) parts the

temperature error will increase by ±0.3˚C for a power supply voltage (V+) variation of ±10% from the nominal value.

For the LM74CIBP-3 (micro SMD) parts all accuracies are guaranteed over the supply range of 2.65V to 3.6V, except for the temperature ranges of -55˚C to 125˚C

and −55˚C to +150˚C where the accuracy applies for the nominal supply voltage of 3.3V. For the LM74CIBP-5 (micro SMD) parts all accuracies are guranteed over

the supply range of 4.75V to 5.25V, except for the temperature ranges of -55˚C to 125˚C and −55˚C to +150˚C where the accuracy applies for the nominal supply

voltage of 5.0V. For the LM74CIBP over -55˚C to 125˚C and −55˚C to +150˚C, a power supply variation of ±10% will degrade the accuracy by ±0.3˚C.

10090905

FIGURE 3. TRI-STATE Data Output Timing Diagram

10090906

FIGURE 4. Data Input Timing Diagram

LM74 Datenblatt(PDF) 6 Page - National Semiconductor (TI)

LM74 Datenblatt(HTML) 6 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Datenblatt Download

Link URL