LPC660AMJSLASH883 datasheet(5/17 Pages) NSC

5 / 17 page

AC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for T

J = 25˚C. Boldface limits apply at the temperature extremes. V

+ = 5V, V−

= 0V, V

CM = 1.5V, VO = 2.5, and RL > 1M unless otherwise specified.

Parameter

Conditions

Typ

LPC660AM

LPC660AI

LPC660I

Units

LPC660AMJ/883

Limit

(Notes 4, 8)

(Note 4)

Slew Rate

(Note 6)

0.11

0.07

0.05

V/µs

0.04

0.05

0.03

min

Gain-Bandwidth Product

0.35

MHz

Phase Margin

Deg

Gain Margin

Amp-to-Amp Isolation

(Note 7)

130

Input Referred Voltage Noise

F = 1 kHz

Input Referred Current Noise

F = 1 kHz

0.0002

Total Harmonic Distortion

F = 1 kHz, A

V = −10

0.01

L = 100 kΩ,VO = 8VPP

Note 1: Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature and/or multiple Op Amp shorts

can result in exceeding the maximum allowed junction temperature of 150˚C. Output currents in excess of ±30 mA over long term may adversely affect reliability.

Note 2: The maximum power dissipation is a function of TJ(max), θJA and TA. The maximum allowable power dissipation at any ambient temperature is PD =

(TJ(max)–TA)θJA.

Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-

tended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The

guaranteed specifications apply only for the test conditions listed.

Note 4: Limits are guaranteed by testing or correlation.

Note 5: V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V ≤ VO ≤ 11.5V. For Sinking tests, 2.5V ≤ VO ≤ 7.5V.

Note 6: V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates.

Note 7: Input referred. V+ = 15V and RL = 100 kΩ connected to V

+/2. Each amp excited in turn with 1 kHz to produce V

O = 13 VPP.

Note 8: A military RETS electrical test specification is available on request. At the time of printing, the LPC660AMJ/883 RETS specification complied fully with the

boldface limits in this column. The LPC660AMJ/883 may also be procured to a Standard Military Drawing specification.

Note 9: For operating at elevated temperatures, the device must be derated based on the thermal resistance

θJA with PD = (TJ–TA)/θJA.

Note 10: All numbers apply for packages soldered directly into a PC board.

Note 11: Do not connect output to V+when V+ is greater than 13V or reliability may be adversely affected.

Typical Performance Characteristics V

S = ± 7.5V, TA = 25˚C unless otherwise specified

Supply Current

vs Supply Voltage

DS010547-27

Input Bias Current

vs Temperature

DS010547-28

Common-Mode Voltage

Range vs Temperature

DS010547-29

LPC660AMJ/883 Datenblatt(PDF) 5 Page - National Semiconductor (TI)

LPC660AMJ/883 Datenblatt(HTML) 5 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Datenblatt Download

Link URL