TM124MBK36B, TM124MBK36R 1048576 BY 36-BIT

TM248NBK36B, TM248NBK36R 2097152 BY 36-BIT

DYNAMIC RAM MODULE

SMMS137E – JANUARY 1991 – REVISEDJUNE 1995

7

POST OFFICE BOX 1443

Voltage range on any pin (see Note 1)

– 1 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 1 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Short-circuit output current

50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power dissipation

9 W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0

°C to 70°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–55

°C to 125°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTE 1: All voltage values are with respect to VSS.

recommended operating conditions

MIN

NOM

MAX

UNIT

VCC

Supply voltage

4.5

5

5.5

V

VIH

High-level input voltage

2.4

6.5

V

VIL

Low-level input voltage (see Note 2)

– 1

0.8

V

TA

Operating free-air temperature

0

70

°C

NOTE 2: The algebraic convention, where the more negative (less positive) limit is designated as minimum, is used for logic-voltage levels only.

electrical characteristics over recommended ranges of supply voltage and operating free-air

temperature (unless otherwise noted)

PARAMETER

TEST CONDITIONS

’124MBK36B-60

’124MBK36B-70

’124MBK36B-80

UNIT

PARAMETER

TEST CONDITIONS

MIN

MAX

MIN

MAX

MIN

MAX

UNIT

VOH

High-level output

voltage

IOH = – 5 mA

2.4

2.4

2.4

V

VOL

Low-level output

voltage

IOL = 4.2 mA

0.4

0.4

0.4

V

II

Input current (leakage)

VCC = 5.5 V,

VI = 0 V to 6.5 V,

All other pins = 0 V to VCC

± 10

± 10

± 10

µA

IO

Output current

(leakage)

VCC = 5.5 V,

VO = 0 V to VCC,

CAS high

± 10

± 10

± 10

µA

ICC1

Read or write cycle

current (see Note 3)

VCC = 5.5 V,

Minimum cycle

945

810

720

mA

ICC2

Standby current

After 1 memory cycle,

RAS and CAS high,

VIH = 2.4 V (TTL)

18

18

18

mA

ICC2

Standby current

After 1 memory cycle,

RAS and CAS high,

VIH = VCC – 0.2 V (CMOS)

9

9

9

mA

ICC3

Average refresh current

(RAS only or CBR)

(see Note 3)

VCC = 5.5 V,

Minimum cycle,

RAS cycling,

CAS high (RAS only),

RAS low after CAS low (CBR)

945

810

720

mA

ICC4

Average page current

(see Note 4)

VCC = 5.5 V,

tPC = minimum,

RAS low,

CAS cycling

810

720

630

mA

NOTES:

3. Measured with a maximum of one address change while RAS = VIL

4. Measured with a maximum of one address change while CAS = VIH