| Datenblatt-Suchmaschine für elektronische Bauteile |
|
ADMV1014ACCZ-R7 Datenblatt(PDF) 33 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADMV1014ACCZ-R7 Datenblatt(HTML) 33 Page - Analog Devices |
|
33 / 42 page ![]() Data Sheet ADMV1014 Rev. A | Page 33 of 42 45 67 89 10 11 12 LO FREQUENCY (GHz) IF I: QUAD_FILTERS = 0 IF I: QUAD_FILTERS = 5 IF I: QUAD_FILTERS = 10 IF I: QUAD_FILTERS = 15 IF Q: QUAD_FILTERS = 0 IF Q: QUAD_FILTERS = 5 IF Q: QUAD_FILTERS = 10 IF Q: QUAD_FILTERS = 15 –40 –80 –75 –65 –55 –45 –70 –60 –50 Figure 113. LO To IF Leakage vs. RF Frequency for Four Different QUAD_FILTERS Settings, fIF = 3.5 GHz (Upper Sideband) VVA TEMPERATURE COMPENSATION Figure 114 shows the conversion gain vs. RF frequency at two different Register 0x0B settings and three different temperatures for IF mode. The recommended value suggested in the Start-Up Sequence section provides the highest conversion gain. If the priority is to decrease the conversion gain variation across temperature, Register 0x0B can be set to 0x726C. However, at this value, the conversion gain is lower at each temperature. 23 25 27 29 31 33 35 37 39 41 43 45 RF FREQUENCY (GHz) +85°C AT REG 0x0B = 0x727C +25°C AT REG 0x0B = 0x727C –40°C AT REG 0x0B = 0x727C +85°C AT REG 0x0B = 0x726C +25°C AT REG 0x0B = 0x726C –40°C AT REG 0x0B = 0x726C 25 –10 –5 0 5 10 15 20 Figure 114. Conversion Gain vs. RF Frequency at Maximum Gain for Various Register 0x0B Settings and Various Temperatures PERFORMANCE BETWEEN DIFFERENTIAL vs. SINGLE-ENDED LO INPUT Figure 115 to Figure 117 show the conversion gain, input IP3 and image rejection performance for operating the ADMV1014 LO input as differential vs. SE. The measurements were performed with 0 dBm LO input power, IF mode, with an IF frequency of 3.5 GHz, upper sideband, and TA = 25°C. 23 25 27 29 31 33 35 37 39 41 43 45 RF FREQUENCY (GHz) LO DIFF LO SE P SIDE LO SE N SIDE 25 0 5 10 15 20 Figure 115. Conversion Gain vs. RF Frequency for Three Different LO Mode Settings, fIF = 3.5 GHz (Upper Sideband) 23 25 27 29 31 33 35 37 39 41 43 45 RF FREQUENCY (GHz) 10 –10 –8 –6 –4 –2 0 2 4 6 8 LO DIFF LO SE P SIDE LO SE N SIDE Figure 116. Input IP3 vs. RF Frequency for Three Different LO Mode Settings, RF Amplitude = −30 dBm per Tone at 20 MHz Spacing, fIF = 3.5 GHz (Upper Sideband) |
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |