ICS1893BFILF datasheet(21/133 Pages) ICST

21 / 133 page

Chapter 4 Operating Modes Overview

ICS1893BF, Rev. C, 9/29/05

September, 2005

ICS1893BF Data Sheet Rev. C - Release

4.5 100Base-TX Operations

The ICS1893BF 100Base-TX mode provides 100Base-TX physical layer (PHY) services as defined in the

ISO/IEC 8802-3 standard. In the 100Base-TX mode, the ICS1893BF is a 100M translator between a MAC

and the physical transmission medium. As such, the ICS1893BF has two interfaces, both of which are fully

configurable: one to the MAC and one to the Link Segment. In 100Base-TX mode, the ICS1893BF provides

the following functions:

• Data conversion from both parallel-to-serial and serial-to-parallel formats

• Data encoding/decoding (4B/5B, NRZ/NRZI, and MLT-3)

• Data scrambling/descrambling

• Data transmission/reception over a twisted-pair medium

To accurately transmit and receive data, the ICS1893BF employs DSP-based wave shaping, adaptive

equalization, and baseline wander correction. In addition, in 100Base-TX mode, the ICS1893BF provides a

variety of control and status means to assist with Link Segment management. For more information on

100Base-TX, see Section 6.4, “Functional Block: 100Base-TX TP-PMD Operations”.

4.6 10Base-T Operations

The ICS1893BF 10Base-T mode provides 10Base-T physical layer (PHY) services as defined in the

ISO/IEC 8802-3 standard. In the 10Base-T mode, the ICS1893BF is a 10M translator between a MAC and

the physical transmission medium. In 10Base-T mode, the ICS1893BF provides the following functions:

• Data conversion from both parallel-to-serial and serial-to-parallel formats

• Manchester data encoding/decoding

• Data transmission/reception over a twisted-pair medium

4.7 Half-Duplex and Full-Duplex Operations

The ICS1893BF supports half-duplex and full-duplex operations for both 10Base-T and 100Base-TX

applications. Full-duplex operation allows simultaneous transmission and reception of data, which

effectively doubles the Link Segment throughput to either 20 Mbps (for 10Base-T operations) or 200 Mbps

(for 100Base-TX operations).

As per the ISO/IEC standard, full-duplex operations differ slightly from half-duplex operations. These

differences are necessary, as during full-duplex operations a PHY actively uses both its transmit and

receive data paths simultaneously.

• In 10Base-T full-duplex operations, the ICS1893BF disables its loopback function (that is, it does not

automatically loop back data from its transmitter to its receiver) and disables its SQE Test function.

• In both 10Base-T and 100Base-TX full-duplex operations, the ICS1893BF asserts its CRS signal only in

response to receive activity while its COL signal always remains inactive.

For more information on half-duplex and full-duplex operations, see the following sections:

• Section 7.2, “Register 0: Control Register”

• Section 7.2.8, “Duplex Mode (bit 0.8)”

• Section 7.3, “Register 1: Status Register”

• Section 7.6, “Register 4: Auto-Negotiation Register”

ICS1893BFILF Datenblatt(PDF) 21 Page - Integrated Circuit Systems

ICS1893BFILF Datenblatt(HTML) 21 Page - Integrated Circuit Systems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL