AM29LV128ML103REF datasheet(30/66 Pages) AMD

30 / 66 page

Am29LV128MH/L

25270C7 January 31, 2007

D A TA

SH EE T

Enter Secured Silicon Sector/Exit Secured

Silicon Sector Command Sequence

The Secured Silicon Sector region provides a secured

data area containing an 8-word/16-byte random Elec-

tronic Serial Number (ESN). The system can access

the Secured Silicon Sector region by issuing the

three-cycle Enter Secured Silicon Sector command

sequence. The device continues to access the Se-

cured Silicon Sector region until the system issues the

four-cycle Exit Secured Silicon Sector command se-

quence. The Exit Secured Silicon Sector command

sequence returns the device to normal operation.

Table 10 and Table 11 show the address and data re-

quirements for both command sequences. See also

“Secured Silicon Sector Flash Memory Region” on

page 24 for further information. Note: The write buffer,

ACC function, and unlock bypass modes are not avail-

able when the Secured Silicon Sector is enabled.

Word Program Command Sequence

Programming is a four-bus-cycle operation. The pro-

gram command sequence is initiated by writing two

unlock write cycles, followed by the program set-up

command. The program address and data are written

next, which in turn initiate the Embedded Program al-

gorithm. The system is not required to provide further

controls or timings. The device automatically provides

internally generated program pulses and verifies the

programmed cell margin. Table 10 and Table 11 show

the address and data requirements for the word pro-

gram command sequence.

When the Embedded Program algorithm is complete,

the device then returns to the read mode and ad-

dresses are no longer latched. The system can deter-

mine the status of the program operation by using

DQ7 or DQ6. See “Wr ite Operation Status” on

page 39 for information on these status bits.

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program

operation. The program command sequence should

be reinitiated once the device has returned to the read

mode, to ensure data integrity. Note that the Secured

Silicon Sector, autoselect, and CFI functions are un-

available when a program operation is in progress.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from “0” back to a “1.” Attempting to do so may

cause the device to set DQ5 = 1, or cause the DQ7

and DQ6 status bits to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0.” Only erase operations can convert a “0”

to a “1.”

Note: Single byte programming is not supported in x8-mode.

Write buffer programming must be used during x8-mode

operation.

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram words to the device faster than using the stan-

dard program command sequence. The unlock bypass

command sequence is initiated by first writing two un-

lock cycles. This is followed by a third write cycle con-

taining the unlock bypass command, 20h. The device

then enters the unlock bypass mode. A two-cycle un-

lock bypass program command sequence is all that is

required to program in this mode. The first cycle in this

sequence contains the unlock bypass program com-

mand, A0h; the second cycle contains the program

address and data. Additional data is programmed in

the same manner. This mode dispenses with the initial

two unlock cycles required in the standard program

command sequence, resulting in faster total program-

ming time. Table 10 and Table 11 show the require-

ments for the command sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence. The first cycle must contain the data

90h. The second cycle must contain the data 00h. The

device then returns to the read mode.

Write Buffer Programming

Write Buffer Programming allows the system write to a

maximum of 16 words/32 bytes in one programming

operation. This results in faster effective programming

time than the standard programming algorithms. The

Write Buffer Programming command sequence is initi-

ated by first writing two unlock cycles. This is followed

by a third write cycle containing the Write Buffer Load

command written at the Sector Address in which pro-

gramming will occur. The fourth cycle writes the sector

address and the number of word locations, minus one,

to be programmed. For example, if the system will pro-

gram 6 unique address locations, then 05h should be

written to the device. This tells the device how many

write buffer addresses will be loaded with data and

therefore when to expect the Program Buffer to Flash

command. The number of locations to program cannot

exceed the size of the write buffer or the operation will

abort.

The fifth cycle writes the first address location and

data to be programmed. The write-buffer-page is se-

lected by address bits A

MAX–A4. All subsequent ad-

dr ess/ dat a

p a ir s

m u s t

f a ll

within

th e

selected-write-buffer-page. The system then writes the

AM29LV128ML103REF Datenblatt(PDF) 30 Page - Advanced Micro Devices

AM29LV128ML103REF Datenblatt(HTML) 30 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

Datenblatt Download

Link URL