LP55231 datasheet(33/59 Pages) TI2

33 / 59 page

LP55231

www.ti.com

SNOSCR5D – MARCH 2013 – REVISED DECEMBER 2016

Product Folder Links: LP55231

Submit Documentation Feedback

•

0 = engine ready.

•

3A — Bit [3] EXT_CLK_USED

•

1 = external clock detected.

•

0 = external clock not detected.

•

This bit is high when external clock signal on CLK pin is detected. CLK_DET_EN bit high in address 36

enables the clock detection.

•

3A — Bits [2:0] ENG1_INT, ENG2_INT, ENG3_INT

•

1 = interrupt set.

•

0 = interrupt unset/cleared.

•

Interrupt bits for program execution engine 1, 2, and 3, respectively. These bits are set by END or INT

instruction. Reading the interrupt bit clears the interrupt.

3B INT/GPO

•

INT pin can be configured to function as a GPO by setting the bit INT_CONF. When INT is configured to

function as a GPO, output level is defined by the VDD voltage.

•

3B — Bit [2] INT_CONF

•

0 = INT pin is set to function as an interrupt pin (default).

•

1 = INT pin is configured to function as a GPO.

•

3B — Bit [0] INT_GPO

•

0 = INT pin state is low (if INT_CONF = 1).

•

1 = INT pin state is high (if INT_CONF = 1).

•

When INT pin’s GPO function is disabled, it operates as an open drain pin. INT signal is active low; that is,

when interrupt signal is sent, the pin is pulled to GND. External pullup resistor is needed for proper

functionality.

3C VARIABLE

•

3C — Bits [7:0] VARIABLE

•

These bits are used for storing a global 8-bit variable. Variable can be used to control program flow.

3D RESET

•

3D — Bits [7:0] RESET

•

Writing 11111111 into this register resets the LP55231. Internal registers are reset to the default values.

Reading RESET register returns 00000000.

3E TEMP ADC CONTROL

•

3E — Bit [7] TEMP_MEAS_BUSY

•

1 = temperature measurement active.

•

0 = temperature measurement done or not activated.

•

3E — Bit [2] EN_TEMP_SENSOR

•

1 = enables internal temperature sensor. Every time when EN_TEMP_SENSOR is written high a new

measurement period is started. The length of the measurement period depends on temperature. At 25°C a

measurement takes 20 milliseconds. Temperature can be read from register 3F.

•

0 = temp sensor disabled.

•

3E — Bit [1] CONTINUOUS _CONV

•

This bit is effective when EN_TEMP_SENSOR = 1.

•

1 = continuous temperature measurement. Not active when the device is in power save.

•

0 = new temperature measurement period initiated during start-up or after exit from power-save mode.

3E — Bit [0] SEL_EXT_TEMP

•

1 = temperature compensation source register addr 40H.

•

0 = temperature compensation source register addr 3FH.

3F TEMPERATURE READ

•

3F — Bits [7:0] TEMPERATURE

•

These bits are used for storing an 8-bit temperature reading acquired from the internal temperature sensor.

LP55231 Datenblatt(PDF) 33 Page - Texas Instruments

LP55231 Datenblatt(HTML) 33 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

Datenblatt Download

Link URL