AS3525 datasheet(97/194 Pages) AMSCO

97 / 194 page

AS3525-A/-B C22O22

Data Sheet, Confidential

www.austriamicrosystems.com

Revision 1.13

- 194

Name

Base

Default

UART_INTSTATUS_REG

AS3525_UART_BASE

0xC8110000

Interrupt status register

Offset: 0x08

This register will give the status of the interrupt. Depending on the enabled interrupt

bits in the interrupt enable register (UART_INTEN_REG) different interrupts will be

generated and the status will be updated in this register. On sensing an interrupt the

software should read this register to get the status of the interrupt.

Bit

Bit Name

Default

Access

Bit Description

rxDataRdy

This is the data ready interrupt.

In FIFO mode this bit is set when the number of bytes in the

FIFO reaches the trigger level. This bit is also set in FIFO

mode when a timeout occurs in the reception, i.e. Rx line idle

for more than 4 char times and there is data in the FIFO.

If FIFO mode is disabled this bit is set when one full byte is

received.

This bit is cleared when the FIFO is empty or the data register

(UART_DATA_REG (Rx)) is read.

Table 82 UART FIFO control register

Name

Base

Default

UART_FCTL_REG

AS3525_UART_BASE

0xC8110000

FIFO control register

Offset: 0x0C

This register holds the control parameters to control receive (rx) and transmit (tx) FIFO.

The parameters will enable the FIFOs, set the receiver trigger level, etc.

Bit

Bit Name

Default

Access

Bit Description

7:5

Reserved

000

These bits are reserved for future use.

4:3

trigLevel

These two bits will select the trigger level for the rxFIFO. Once

the FIFO pointer reaches this level rxDataRdy interrupt is

asserted.

00: 01 byte

01: 04 bytes

10: 08 bytes

11: 14 bytes

rxFIFORst

This bit will reset rxFIFO pointers and clear all the bytes in the

rxFIFO.

This bit is self clearing, i.e. after resetting FIFO this bit will

become zero.

txFIFORst

This bit will reset txFIFO pointers and clear all the bytes in the

txFIFO.

This bit is self clearing, i.e. after resetting FIFO this bit will

become zero.

FIFOModeEn

This bit will enable the FIFO mode. By default this will be

reset.

Table 83 UART Line control register

Name

Base

Default

UART_LNCTL_REG

AS3525_UART_BASE

0xC8110000

Line control register

Offset: 0x10

This register controls the asynchronous data. Parameters in this register set the

transmit and receive character format, the data length, parity bit, stop bit length, etc.

Bit

Bit Name

Default

Access

Bit Description

AS3525 Datenblatt(PDF) 97 Page - ams AG

AS3525 Datenblatt(HTML) 97 Page - ams AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL