TMS570LS3134 datasheet(3/155 Pages) TI1

3 / 155 page

TMS570LS3134

TMS570LS2134

TMS570LS2124

www.ti.com

SPNS165

– SEPTEMBER 2011

1.3

Description

The TMS570LSxxx4 is a high performance automotive grade microcontroller family for safety systems.

The safety architecture includes Dual CPUs in lockstep, CPU and Memory Built-In Self Test (BIST) logic,

ECC on both the Flash and the data SRAM, parity on peripheral memories, and loop back capability on

peripheral IOs.

The TMS570LSxxx4 integrates the ARM

® Cortex™-R4F Floating Point CPU which offers an efficient 1.6

DMIPS/MHz, and has configurations which can run up to 180MHz providing up to 288 DMIPS. The device

supports the big-endian [BE32] format.

The TMS570LSxxx4 has up to 3MB integrated Flash and up to 256KB data RAM configurations with

single bit error correction and double bit error detection. The flash memory on this device is a nonvolatile,

electrically erasable and programmable memory implemented with a 64-bit-wide data bus interface. The

flash operates on a 3.3V supply input (same level as I/O supply) for all read, program and erase

operations. When in pipeline mode, the flash operates with a system clock frequency of up to 180MHz.

The SRAM supports single-cycle read/write accesses in byte, halfword, and word modes.

The TMS570LSxxx4 device features peripherals for real-time control-based applications, including two

Next Generation High End Timer (N2HET) timing coprocessors with up to 44 total IO terminals and a

12-bit Analog-to-Digital converter supporting up to 24 inputs.

The N2HET is an advanced intelligent timer that provides sophisticated timing functions for real-time

applications. The timer is software-controlled, using a reduced instruction set, with a specialized timer

micromachine and an attached I/O port. The N2HET can be used for pulse width modulated outputs,

capture or compare inputs, or general-purpose I/O. It is especially well suited for applications requiring

multiple sensor information and drive actuators with complex and accurate time pulses. A High End Timer

Transfer Unit (HET-TU) can perform DMA type transactions to transfer N2HET data to or from main

memory. A Memory Protection Unit (MPU) is built into the HET-TU.

The device has two 12-bit-resolution MibADCs with 24 total channels and 64 words of parity protected

buffer RAM each. The MibADC channels can be converted individually or can be grouped by software for

sequential conversion sequences. Sixteen channels are shared between the two MibADCs. There are

three separate groupings. Each sequence can be converted once when triggered or configured for

continuous conversion mode.

The device has multiple communication interfaces: three MibSPIs, up to two SPIs, one LIN, one SCI, three

DCANs, one I2C, one Ethernet. The SPI provides a convenient method of serial interaction for high-speed

communications between similar shift-register type devices. The LIN supports the Local Interconnect

standard 2.0 and can be used as a UART in full-duplex mode using the standard Non-Return-to-Zero

(NRZ) format. The DCAN supports the CAN 2.0B protocol standard and uses a serial, multimaster

communication protocol that efficiently supports distributed real-time control with robust communication

rates of up to 1 megabit per second (Mbps). The DCAN is ideal for applications operating in noisy and

harsh environments (e.g., automotive and industrial fields) that require reliable serial communication or

multiplexed wiring. The Ethernet module supports MII and MDIO interfaces.

The I2C module is a multi-master communication module providing an interface between the

microcontroller and an I2C compatible device via the I2C serial bus. The I2C supports both 100 Kbps and

400 Kbps speeds.

The frequency-modulated phase-locked loop (FMPLL) clock module is used to multiply the external

frequency reference to a higher frequency for internal use. The FMPLL provides one of the seven possible

clock source inputs to the global clock module (GCM). The GCM module manages the mapping between

the available clock sources and the device clock domains.

The device also has an external clock prescaler (ECP) module that when enabled, outputs a continuous

external clock on the ECLK pin/ball. The ECLK frequency is a user-programmable ratio of the peripheral

interface clock (VCLK) frequency. This low frequency output can be monitored externally as an indicator of

the device operating frequency.

TMS570LSxxx4 16/32-Bit RISC Flash Microcontroller

Submit Documentation Feedback

focus.ti.com: TMS570LS3134 TMS570LS2134 TMS570LS2124

TMS570LS3134 Datenblatt(PDF) 3 Page - Texas Instruments

TMS570LS3134 Datenblatt(HTML) 3 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL