| Datenblatt-Suchmaschine für elektronische Bauteile |
|
PIC24F16KA102T-E Datenblatt(PDF) 232 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC24F16KA102T-E Datenblatt(HTML) 232 Page - Microchip Technology |
|
232 / 278 page ![]() PIC24F16KA102 FAMILY DS39927C-page 232 2008-2011 Microchip Technology Inc. FIGURE 29-5: EXTERNAL CLOCK TIMING OSCI CLKO Q4 Q1 Q2 Q3 Q4 Q1 OS20 OS25 OS30 OS30 OS40 OS41 OS31 OS31 Q1 Q2 Q3 Q4 Q2 Q3 TABLE 29-19: EXTERNAL CLOCK TIMING REQUIREMENTS AC CHARACTERISTICS Standard Operating Conditions: 1.8 to 3.6V (unless otherwise stated) Operating temperature -40°C TA +85°C for Industrial -40°C TA +125°C for Extended Param No. Sym Characteristic Min Typ(1) Max Units Conditions OS10 FOSC External CLKI Frequency (External clocks allowed only in EC mode)(2) DC 4 — — 32 8 MHz MHz EC ECPLL Oscillator Frequency(2) 0.2 4 4 31 — — — — 4 25 8 33 MHz MHz MHz kHz XT HS HSPLL SOSC OS20 TOSC TOSC = 1/FOSC — — — — See Parameter OS10 for FOSC value OS25 TCY Instruction Cycle Time(3) 62.5 — DC ns OS30 TosL, TosH External Clock in (OSCI) High or Low Time 0.45 x TOSC —— ns EC OS31 TosR, TosF External Clock in (OSCI) Rise or Fall Time —— 20 ns EC OS40 TckR CLKO Rise Time(4) —6 10 ns OS41 TckF CLKO Fall Time(4) —6 10 ns Note 1: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Refer to Figure 29-1 for the minimum voltage at a given frequency. 3: Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “Min.” values with an external clock applied to the OSCI/CLKI pin. When an external clock input is used, the “Max.” cycle time limit is “DC” (no clock) for all devices. 4: Measurements are taken in EC mode. The CLKO signal is measured on the OSCO pin. CLKO is low for the Q1-Q2 period (1/2 TCY) and high for the Q3-Q4 period (1/2 TCY). |
|
Link URL |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Link zum Datenblatt | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |