AT90USB646 datasheet(30/434 Pages) ATMEL

30 / 434 page

7593A–AVR–02/06

AT90USB64/128

When the XMEM interface is enabled, the XMEM interface will override the setting in the data

direction registers that corresponds to the ports dedicated to the XMEM interface. For details

about the port override, see the alternate functions in section “I/O-Ports” on page 73. The XMEM

interface will auto-detect whether an access is internal or external. If the access is external, the

XMEM interface will output address, data, and the control signals on the ports according to Fig-

ure 5-6 (this figure shows the wave forms without wait-states). When ALE goes from high-to-low,

there is a valid address on AD7:0. ALE is low during a data transfer. When the XMEM interface

is enabled, also an internal access will cause activity on address, data and ALE ports, but the

RD and WR strobes will not toggle during internal access. When the External Memory Interface

is disabled, the normal pin and data direction settings are used. Note that when the XMEM inter-

face is disabled, the address space above the internal SRAM boundary is not mapped into the

internal SRAM. Figure 5-5 illustrates how to connect an external SRAM to the AVR using an

octal latch (typically “74 x 573” or equivalent) which is transparent when G is high.

5.5.3

Address Latch Requirements

Due to the high-speed operation of the XRAM interface, the address latch must be selected with

care for system frequencies above 8 MHz @ 4V and 4 MHz @ 2.7V. When operating at condi-

tions above these frequencies, the typical old style 74HC series latch becomes inadequate. The

External Memory Interface is designed in compliance to the 74AHC series latch. However, most

latches can be used as long they comply with the main timing parameters. The main parameters

for the address latch are:

• D to Q propagation delay (t

PD).

• Data setup time before G low (t

SU).

• Data (address) hold time after G low (

TH).

The External Memory Interface is designed to guaranty minimum address hold time after G is

asserted low of t

h = 5 ns. Refer to tLAXX_LD/tLLAXX_ST in “External Data Memory Timing” Tables 30-

7 through Tables 30-13 on pages 408 - 411. The D-to-Q propagation delay (t

PD) must be taken

into consideration when calculating the access time requirement of the external component. The

data setup time before G low (t

SU) must not exceed address valid to ALE low (tAVLLC) minus PCB

wiring delay (dependent on the capacitive load).

Figure 5-5.

External SRAM Connected to the AVR

D[7:0]

A[7:0]

A[15:8]

SRAM

AD7:0

ALE

A15:8

AVR

AT90USB646 Datenblatt(PDF) 30 Page - ATMEL Corporation

AT90USB646 Datenblatt(HTML) 30 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL