PA62 datasheet(2/4 Pages) APEX

2 / 4 page

APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: 1 (800) 546-2739

PARAMETER

TEST CONDITIONS1,2

MIN

TYP

MAX

UNTS

INPUT

OFFSET VOLTAGE, initial

OFFSET VOLTAGE, vs. temperature

Full temp range

µV/°C

BIAS CURRENT, initial

100

500

COMMON MODE RANGE

Full temp range

-Vs

+Vs

COMMON MODE REJECTION, DC

POWER SUPPLY REJECTION

Full temp range

CHANNEL SEPARATION

OUT = 500mA, ƒ = 1kHz

INPUT NOISE VOLTAGE

S = 100Ω, ƒ = 1 to 100kHz

nV/√Hz

GAIN

OPEN LOOP GAIN

O = ±10V, RL = 2.0KΩ

100

GAIN BANDWIDTH PRODUCT

ƒ = 100kHz, C

L = 100pF, RL = 2.0KΩ

0.9

1.4

MHz

PHASE MARGIN

Full temp range

°C

POWER BANDWIDTH

O(P-P) = 28V

13.6

kHz

OUTPUT

CURRENT, peak

1.0

SLEW RATE

1.0

1.4

V/µS

VOLTAGE SWING

Full temp range, I

O = 100mA

|Vs| -1.1

|Vs| -0.8

VOLTAGE SWING

Full temp range, I

O = 1A

|Vs| -1.8

|Vs| -1.4

HARMONIC DISTORTION

V = 1, RL = 50Ω,

.02

O = .5VRMS, ƒ = 1kHz

POWER SUPPLY

VOLTAGE, Vss3

CURRENT, quiescent +Vs (A/B)

CURRENT, quiescent +Vs (C/D)

CURRENT, quiescent total

THERMAL

RESISTANCE, junction to case

DC, 1 ampliﬁer

7.16

7.87

°C/W

DC, 2 ampliﬁers4

4.69

5.16

°C/W

DC, 3 ampliﬁers4

3.08

3.39

°C/W

DC, 4 ampliﬁers4

2.51

2.77

°C/W

AC, 1 ampliﬁer

5.37

5.90

°C/W

AC, 2 ampliﬁers4

3.52

3.87

°C/W

AC, 3 ampliﬁers4

2.31

2.54

°C/W

AC, 4 ampliﬁers4

1.89

2.07

°C/W

RESISTANCE, junction to air6

°C/W

ABSOLUTE MAXIMUM RATINGS

SPECIFICATIONS

ABSOLUTE MAXIMUM RATINGS

PA62

Notes

1. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation to

achieve high MTTF.

2. Unless otherwise noted, the following conditions apply: ±V

S = ±15V, T C =25°C.

3. +V

S and -VS denote the positive and negative rail respectively. VSS denotes total rail-to-rail supply.

4. Rating applies when power dissipation is equal in each of the ampliﬁers. Power and thermal ratings are based on two separate

dual monolithic power op-amps on one integrated copper heatslug. Ampliﬁers A and B are combined on one monolithic die while

ampliﬁers C and D are on the other.

5. If -V

S is disconnected before +VS, a diode between -VS and ground is recommended to avoid damage.

6. Rating applies when the heatslug of the DK package is soldered to a minimum of 1 square inch foil area of a printed circuit

board.

SUPPLY VOLTAGE, total

5V to 40V

OUTPUT CURRENT

SOA

POWER DISSIPATION, internal (1 ampliﬁer)

15.88W

POWER DISSIPATION, internal (2 ampliﬁers)4

24.21W

POWER DISSIPATION, internal (3 ampliﬁers)4

36.90W

POWER DISSIPATION, internal (4 ampliﬁers)4

45.20W

INPUT VOLTAGE, differential

±Vs

INPUT VOLTAGE, common mode

+Vs,-Vs-.5V

JUNCTION TEMPERATURE, max1

150°C

TEMPERATURE, pin solder - 10 secs max.

220°C

TEMP RANGE STORAGE

-55°C to 150°C

OPERATING TEMP RANGE, case1

-40°C to 125°C

SPECIFICATIONS (PER AMPLIFIER)

PA62 Datenblatt(PDF) 2 Page - Cirrus Logic

PA62 Datenblatt(HTML) 2 Page - Cirrus Logic

Html Pages

1 2 3 4

Datenblatt Download

Link URL