MCP3901 datasheet(5/62 Pages) MICROCHIP

5 / 62 page

DS22192D-page 5

MCP3901

AC Power Supply Rejection

AC PSRR

—

-77

—

AVDD and DVDD = 5V +

1VPP @ 50/60 Hz

DC Power Supply Rejection

DC PSRR

—

-77

—

AVDD and DVDD = 4.5 to

5.5V

DC Common-Mode Rejection

Ratio (Note 2)

CMRR

—

-72

—

VCM varies from -1V to

+1V

Oscillator Input

Master Clock Frequency Range

MCLK

—

16.384

MHz

(Note 8)

Power Specifications

Operating Voltage, Analog

AVDD

4.5

—

5.5

Operating Voltage, Digital

DVDD

2.7

3.6

5.5

Power On Reset Threshold

POR

—

4.2

—

(Note 3)

—

4.6

—

-40°C < TA < 125°C,

(Note 3)

Operating Current, Analog

(Note 4)

AIDD

—

2.1

2.8

BOOST<1:0> = 00

—

2.1

3.3

-40°C < TA < 125°C,

BOOST<1:0> = 00

—

3.8

5.6

BOOST<1:0> = 11

—

3.8

-40°C < TA < 125°C,

BOOST<1:0> = 11

Operating Current, Digital

DIDD

—0.45

1.0

DVDD = 5V,

MCLK = 4 MHz

—

0.25

0.45

DVDD = 2.7V,

MCLK = 4 MHz

—1.2

1.6

DVDD = 5V,

MCLK = 8.192 MHz

Shutdown Current, Analog

IDDS,A

——

µA

AVDD pin only (Note 5)

Shutdown Current, Digital

IDDS,D

——

µA

DVDD pin only (Note 5)

ELECTRICAL CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise indicated, AVDD = 4.5 to 5.5V, DVDD = 2.7 to 5.5V; -40°C < TA < +85°C,

MCLK = 4 MHz; PRESCALE = 1; OSR = 64; GAIN = 1; Dithering OFF; VIN = -0.5 dBFS = 333 mVRMS @ 50/60 Hz

Parameters

Symbol

Min

Typical

Max

Units

Conditions

Note 1:

This specification implies that the ADC output is valid over this entire differential range and that there is no

distortion or instability across this input range. Dynamic performance is specified at -0.5 dB below the

maximum signal range, VIN = -0.5 dBFS @ 50/60 Hz = 353 mVRMS, VREF = 2.4V.

See terminology section for definition.

This parameter is established by characterization and not 100% tested.

For these operating currents, the following bit settings apply: SHUTDOWN<1:0> = 00, RESET<1:0> = 00,

VREFEXT = 0, CLKEXT = 0.

For these operating currents, the following Configuration bit settings apply: SHUTDOWN<1:0> = 11,

VREFEXT = 1, CLKEXT = 1.

Applies to all gains. Offset error is dependant on PGA gain setting (see Figure 2-19 for typical values).

Outside of this range, the ADC accuracy is not specified. An extended input range of ±6V can be applied

continuously to the part with no risk for damage.

For proper operation and to keep ADC accuracy, AMCLK should always be in the range of 1 to 5 MHz with

BOOST bits off. With BOOST bits on, AMCLK should be in the range of 1 to 8.192 MHz,

AMCLK = MCLK/PRESCALE. When using a crystal, the CLKEXT bit should be equal to ‘0’.

MCP3901 Datenblatt(PDF) 5 Page - Microchip Technology

MCP3901 Datenblatt(HTML) 5 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

Datenblatt Download

Link URL