HT46R92 datasheet(37/61 Pages) HOLTEK

37 / 61 page

HT46R92

Rev. 1.10

November 5, 2008

· Low Voltage Reset

- LVR

The microcontroller contains a low voltage reset cir-

cuit in order to monitor the supply voltage of the de-

vice. The LVR function is selected via a configuration

option. If the supply voltage of the device drops to

within a range of 0.9V~VLVR such as might occur when

changing the battery, the LVR will automatically reset

the device internally. For a valid LVR signal, a low sup-

ply voltage, i.e., a voltage in the range between

0.9V~VLVR must exist for a time greater than that spec-

ified by tLVR in the A.C. characteristics. If the low sup-

ply voltage state does not exceed this value, the LVR

will ignore the low supply voltage and will not perform

a reset function. The actual VLVR value can be se-

lected via configuration options.

· Watchdog Time-out Reset during Normal Operation

The Watchdog time-out Reset during normal opera-

tion is the same as a hardware RES pin reset except

that the Watchdog time-out flag TO will be set to

²1².

· Watchdog Time-out Reset during Power Down

The Watchdog time-out Reset during Power Down is

a little different from other kinds of reset. Most of the

conditions remain unchanged except that the Pro-

gram Counter and the Stack Pointer will be cleared to

²0² and the TO flag will be set to ²1². Refer to the A.C.

Characteristics for tSST details.

Reset Initial Conditions

The different types of reset described affect the reset

flags in different ways. These flags, known as PDF and

TO are located in the status register and are controlled

by various microcontroller operations, such as the

Power Down function or Watchdog Timer. The reset

flags are shown in the table:

TO PDF

RESET Conditions

RES reset during power-on

RES or LVR reset during normal operation

WDT time-out reset during normal operation

WDT time-out reset during Power Down

Note:

²u² stands for unchanged

The following table indicates the way in which the vari-

ous components of the microcontroller are affected after

a power-on reset occurs.

Item

Condition After RESET

Program Counter

Reset to zero

Interrupts

All interrupts will be disabled

WDT

Clear after reset, WDT begins

counting

Timer/Event

Counter

Timer Counter will be turned off

Prescaler

The Timer Counter Prescaler will

be cleared

Input/Output Ports

I/O ports will be setup as inputs

Stack Pointer

Stack Pointer will point to the top

of the stack

The different kinds of resets all affect the internal regis-

ters of the microcontroller in different ways. To ensure

reliable continuation of normal program execution after

a reset occurs, it is important to know what condition the

microcontroller is in after a particular reset occurs. The

accompanying table describes how each type of reset

affects each of the microcontroller internal registers.

W D T T i m e - o u t

S S T T i m e - o u t

t S S T

WDT Time-out Reset during Power Down

Timing Chart

W D T T i m e - o u t

S S T T i m e - o u t

I n t e r n a l R e s e t

t R S T D

WDT Time-out Reset during Normal Operation

Timing Chart

L V R

S S T T i m e - o u t

I n t e r n a l R e s e t

t R S T D

Low Voltage Reset Timing Chart

HT46R92 Datenblatt(PDF) 37 Page - Holtek Semiconductor Inc

HT46R92 Datenblatt(HTML) 37 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

Datenblatt Download

Link URL