STW82102B datasheet(16/67 Pages) STMICROELECTRONICS

16 / 67 page

Electrical characteristics

STW82102B

16/67

Doc ID 018516 Rev 2

Phase Flatness for TX

observation path(5)

Maximum deviation from linear phase

at Fc over ±10 MHz. For any Fc within

each TX observation path band.

-0.3

+0.3

deg

Maximum deviation from linear phase

at Fc over ±30 MHz. For any Fc within

each TX observation path band.

-0.7

+0.7

deg

Gain Flatness for RX path(5)

Maximum ripple over a 4 MHz band.

For any Fc within each RX path band.

0.1

pk-pk

Phase Flatness for RX path(5)

Maximum ripple over a 4 MHz band.

For any Fc within each RX path band.

0.6

deg

pk-pk

ICCMD

Mixer Driver Current

Consumption

3.3 V Supply (pin 41, 42)

5 V Supply (pin 40)

Mixer Driver Current

Consumption (Low Current

Mode)

3.3 V Supply (pin 41, 42)

3.3 V Supply (pin 40)

ICCIFAM

IFAMP Current Consumption

3.3 V Supply (pin 33)

5 V Supply (pin 31, 32)

107

IFAMP Current Consumption

(Low Current Mode)

3.3 V Supply (pin 33)

3.3 V Supply (pin 31, 32)

All linearity and NF performances are intended at maximum LO amplitude (LO_A[1:0]=[11]), tuning capacitors (CAP[2:0])

programmed according to the selected frequency, mixer bias (MIX[3:0]) set to maximize performance and the device

operated in high current mode. The performances of conversion gain, NF and linearity are intended at the SMA connectors

of a typical application board.

The IF frequency range supported by the IF Amplifier is from 70 to 400 MHz. The exact IF frequency range supported for a

specific RF frequency can be calculated as FIF = ABS(FLO-FRF) where FLO is inside the specified LO frequency range.

Guaranteed by design and characterization

RFin = 0 dBm/tone, RF tone spacing = 5 MHz

Guaranteed by design

Table 6.

Down converter mixer and IF amplifier electrical characteristics(1) (continued)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

Table 7.

Pin diode attenuator driver (dual output current DAC) electrical characteristics

Symbol

Parameters

Conditions

Min

Typ

Max

Unit

Resolution

Bit

DNL

Differential non linearity

-0.05

0.05

LSB

INL

Integral non linearity

-0.45

0.45

LSB

IFS

Full Scale current (1)

-0.28

2.8

Current Mismatch

Output voltage compliance

range

-0

VREXT_DAC

Voltage Reference

1.19

REXT_DAC

REXT DAC Range

100

Iccstatic

Static current consumption

(Iout = 0 mA; pin 1)

2.5

See relationship between IDAC and REXT_DAC in the Circuit Description section (Dual Output Current DAC)

STW82102B Datenblatt(PDF) 16 Page - STMicroelectronics

STW82102B Datenblatt(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

Datenblatt Download

Link URL