CC1020-RTR1 datasheet(60/95 Pages) TI1

60 / 95 page

CC1020

SWRS046H – NOVEMBER 2006 – REVISED MARCH 2015

www.ti.com

5.20.6 Frequency Hopping Spread Spectrum Systems (FHSS)

Due to the very fast locking properties of the PLL, the CC1020 is also very suitable for frequency hopping

systems. Hop rates of 1to100 hops/s are commonly used depending on the bit rate and the amount of

data to be sent during each transmission. The two frequency registers (FREQ_A and FREQ_B) are

designed such that the ‘next’ frequency can be programmed while the ‘present’ frequency is used. The

switching between the two frequencies is done through the MAIN register. Several features have been

included to do the hopping without a need to re-synchronize the receiver. For more details, refer to

Application Note AN014 Frequency Hopping Systems (SWRA077).

In order to implement a frequency hopping system with CC1020 do the following:

Set the desired frequency, calibrate and store the following register settings in non-volatile memory:

STATUS1[3:0]: CHP_CURRENT[3:0]

STATUS2[4:0]: VCO_ARRAY[4:0]

TEST1[3:0]: CHP_CO[3:0]

STATUS3[5:0]:VCO_CAL_CURRENT[5:0]

Repeat the calibration for each desired frequency. VCO_CAL_CURRENT[5:0] is not dependent on the RF

frequency and the same value can be used for all frequencies.

When performing frequency hopping, write the stored values to the corresponding TEST1, TEST2 and

TEST3 registers, and enable override:

TEST2[4:0]: VCO_AO[4:0]

TEST2[5]: VCO_OVERRIDE

TEST2[6]: CHP_OVERRIDE

TEST3[5:0]: VCO_CO[5:0]

TEST3[6]: VCO_CAL_OVERRIDE

CHP_CO[3:0] is the register setting read from CHP_CURRENT[3:0], VCO_AO[4:0] is the register setting

read

from

VCO_ARRAY[4:0]

and

VCO_CO[5:0]

the

setting

read

from

VCO_CAL_CURRENT[5:0].

Assume channel 1 defined by register FREQ_A is currently being used and that CC1020 should operate

on channel 2 next (to change channel simply write to register MAIN[6]). The channel 2 frequency can be

set by register FREQ_B which can be written to while operating on channel 1. The calibration data must

be written to the TEST1-3 registers after switching to the next frequency. That is, when hopping to a new

channel write to register MAIN[6] first and the test registers next. The PA should be switched off between

each hop and the PLL should be checked for lock before switching the PA back on after a hop has been

performed.

NOTE

The override bits VCO_OVERRIDE, CHP_OVERRIDE and VCO_CAL_OVERRIDE must be

disabled when performing a re-calibration.

Detailed Description

Submit Documentation Feedback

Product Folder Links: CC1020

CC1020-RTR1 Datenblatt(PDF) 60 Page - Texas Instruments

CC1020-RTR1 Datenblatt(HTML) 60 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95

Datenblatt Download

Link URL