AX88658AB datasheet(8/36 Pages) ASIX

8 / 36 page

ASIX ELECTRONICS CORPORATION

AX88658AB 8-Port 10/100/1000BASE-T Ethernet Switch

CONFIDENTIAL

2.0 I/O Definition

The following terms describe the AX88658A pin-out:

All pin names with the “/” suffix are asserted low.

The following abbreviations are used in following Tables.

Input

Pull Up

Output

Pull Down

I/O

Input/Output

Power Pin

Open Drain

ODBI

Open drain with BI-direction

2.1 RGMII/GMII/MII Interface

2.1.1 RGMII/GMII/MII Interface Port 0

Signal Name

I/O

Pin No.

Description

GTX_CLK0

125MHz Clock Output: it is a continuous 125 MHz clock output to

giga-PHY operating at 1000BASE-T. That is, it is a timing reference for

TX_EN0 and TXD0[7:0]

TX_EN0

Transmit Enable: When TX_EN0 is asserted, data on TXD0[7:0] are

transmitted onto PHY. TX_EN0 is synchronous to GTX_CLK0 in

1000BASE-T mode and synchronous to TX_CLK0 in 10/100BASE-T

mode.

TXD0[7:0]

W1, V2, V1,

U3, U2,U1 ,

T2, T1

Transmit Data: Synchronous to the rising of GTX_CLK0 in

1000BASE-T mode. And synchronous to rising edge of TX_CLK0 in

10/100BASE-T mode., For RGMII, only TXD0[3:0]

TX_CLK0

I/PD

MII

Transmit

Clock

Input:

TX_EN0 and TXD0[3:0] are

synchronous to the rising edge of this clock in 10/100BASE-T mode.

COL0

I/PD

Collision Detect: Active high to indicate that there is collision occurred

in half duplex mode. In full duplex mode COL0 is always low.

CRS0

I/PD

Carrier Sense: Active high if there is carrier on medium. In half duplex

mode CRS0 is also asserted during transmission and asynchronous to

any clock.

RX_DV0

Receive Data Valid: Active high to indicate that data presented on

RXD0[7:0] is valid and synchronous to RX_CLK0.

RX_CLK0

Receive Clock Input: 125, 25 and 2.5 MHz is running at 1000/100/10

BASE-T mode respectively.

RX_DV0 and RXD0[7:0] are

synchronous to rising edge of this clock.

RXD0[7:0]

I/PD

U4, V4, W4,

Y4, V3, W3,

Y3, W2

Receive Data: Data received by the PHY are presented on RXD0 and

synchronous

RX_CLK0.

RXD0[3:0]

valid

10/100/1000BASE-T and RXD[7:4] is valid only in 1000BASE-T

modes. For RGMII, only RXD0[3:0]

2.1.2 RGMII/GMII/MII Interface Port 1

Signal Name

I/O

Pin No.

Description

GTX_CLK1

125MHz Clock Output: Please references section 2.1.1.

TX_EN1

Transmit Enable: Please references section 2.1.1.

TXD1[7:0]

W8, Y8,

V7, W7, Y7,

V6, W6, Y6

Transmit Data: Please references section 2.1.1.

TX_CLK1

I/PD

U11

MII Transmit Clock Input: Please references section 2.1.1.

AX88658AB Datenblatt(PDF) 8 Page - ASIX Electronics Corporation

AX88658AB Datenblatt(HTML) 8 Page - ASIX Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

Datenblatt Download

Link URL