M500000013 datasheet(36/70 Pages) SPANSION

36 / 70 page

May 19, 2003

Am50DL9608G

P R E L I M I NARY

Sector command sequence. The device continues to

access the SecSi Sector region until the system is-

sues the four-cycle Exit SecSi Sector command se-

quence. The Exit SecSi Sector command sequence

returns the device to normal operation. The SecSi

Sector is not accessible when the device is executing

an Embedded Program or embedded Erase algorithm.

Table 22 shows the address and data requirements for

both command sequences. Note that the ACC function

and unlock bypass modes are not available when the

SecSi sector is enabled. See also “SecSi™ (Secured

Silicon) Sector SectorFlash Memory Region” for further

information.

Program Command Sequence

Programming is a four-bus-cycle operation. The pro-

gram command sequence is initiated by writing two

unlock write cycles, followed by the program set-up

command. The program address and data are written

next, which in turn initiate the Embedded Program al-

gorithm. The system is not required to provide further

controls or timings. The device automatically provides

internally generated program pulses and verifies the

programmed cell margin. Table 22 shows the address

and data requirements for the byte program command

sequence. Note that the SecSi Sector, autoselect, and

CFI functions are unavailable when a program opera-

tion is in progress.

When the Embedded Program algorithm is complete,

that bank then returns to the read mode and ad-

dresses are no longer latched. The system can deter-

mine the status of the program operation by using

DQ7, DQ6, or RY/BY#. Refer to the Flash Write Oper-

ation Status section for information on these status

bits.

Any commands written to the device during the Em-

bedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program

operation. The program command sequence should

be reinitiated once that bank has returned to the read

mode, to ensure data integrity.

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from “0” back to a “1.” Attempting to do so may

cause that bank to set DQ5 = 1, or cause the DQ7 and

DQ6 status bits to indicate the operation was success-

ful. However, a succeeding read will show that the

data is still “0.” Only erase operations can convert a

“0” to a “1.”

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to pro-

gram bytes or words to a bank faster than using the

standard program command sequence. The unlock

bypass command sequence is initiated by first writing

two unlock cycles. This is followed by a third write

cycle containing the unlock bypass command, 20h.

That bank then enters the unlock bypass mode. A

two-cycle unlock bypass program command sequence

is all that is required to program in this mode. The first

cycle in this sequence contains the unlock bypass pro-

gram command, A0h; the second cycle contains the

program address and data. Additional data is pro-

grammed in the same manner. This mode dispenses

with the initial two unlock cycles required in the stan-

dard program command sequence, resulting in faster

total programming time. Table 22 shows the require-

ments for the command sequence.

During the unlock bypass mode, only the Unlock By-

pass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset com-

mand sequence (See Table 12).

The device offers accelerated program operations

through the WP#/ACC pin. When the system asserts

HH on the WP#/ACC pin, the device automatically en-

ters the Unlock Bypass mode. The system may then

write the two-cycle Unlock Bypass program command

sequence. The device uses the higher voltage on the

WP#/ACC pin to accelerate the operation. Note that

the WP#/ACC pin must not be at V

HH any operation

other than accelerated programming, or device dam-

age may result. In addition, the WP#/ACC pin must not

be left floating or unconnected; inconsistent behavior

of the device may result.

Figure 3 illustrates the algorithm for the program oper-

ation. Refer to the Erase and Program Operations

table in the AC Characteristics section for parameters,

and Figure 16 for timing diagrams.

M500000013 Datenblatt(PDF) 36 Page - SPANSION

M500000013 Datenblatt(HTML) 36 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

Datenblatt Download

Link URL