Changes from Revision C (April 2020) to Revision D (March 2023)

Page

• Changed standard name from: "DIN V VDE V 0884-11:2017-01" to: "DIN EN IEC 60747-17 (VDE 0884-17)"

throughout the document....................................................................................................................................1

• Removed references to standard IEC/EN/CSA 60950-1 throughout the document...........................................1

• Removed standard revision and year references from all standard names throughout the document ............. 1

• Added Maximum impulse voltage (VIMP) specification per DIN EN IEC 60747-17 (VDE 0884-17)....................8

• Changed test conditions and values of Maximum surge isolation voltage (VIOSM) specification per DIN EN IEC

60747-17 (VDE 0884-17)................................................................................................................................... 8

• Clarified method b test conditions of Apparent charge (qPD)..............................................................................8

• Changed working voltage lifetime margin from: 87.5% to: 50%, minimum required insulation lifetime from:

37.5 years to: 30 years and insulation lifetime per TDDB from: 135 years to: 169 years in per DIN EN IEC

60747-17 (VDE 0884-17)................................................................................................................................. 23

• Changed Figure 8-5 per DIN EN IEC 60747-17 (VDE 0884-17)......................................................................23

Changes from Revision B (March 2017) to Revision C (April 2020)

Page

• Made editorial and cosmetic changes throughout the document ...................................................................... 1

• Changed From: "Isolation Barrier Life: >40 Years" To: " >100-year projected lifetime at 1500 VRMS working

voltage" in Section 1 ..........................................................................................................................................1

• Added "Up to 5000 VRMS isolation rating" in Section 1 ..................................................................................... 1

• Added "Up to 12.8 kV surge capability" in Section 1 .........................................................................................1

• Added "±8 kV IEC 61000-4-2 contact discharge protection across isolation barrier" in Section 1 .................... 1

• Added "Automotive version available: ISO7710-Q1" in Section 1 .....................................................................1

• Changed From: "VDE Reinforced Insulation per DIN V VDE V 0884-10 (VDE V 0884-10):2006-12" To: "VDE

reinforced insulation per DIN VDE V 0884-11:2017-01" in Section 1 ................................................................1

• Combined CSA, CQC, and TUV bullets into a single bullet with standard names in Section 1 ........................ 1

• Deleted "VDE, UL, CSA, and TUV Certifications for DW-16 package complete; all other certifications

planned" bullet in Section 1 ............................................................................................................................... 1

• Updated Simplified Schematic to show two isolation capacitors in series instead of a single

isolation capacitor...............................................................................................................................................1

•

Added "Contact discarge per IEC 61000-4-2" specification of 8000V .............................................................5

• Changed "Signaling rate" to "Data rate" and added table note.......................................................................... 6

• Updated DW-16 package VIORM and VIOWM values........................................................................................... 8

• Added TDDB figure reference to VIOWM ............................................................................................................ 8

• Updated VIOSM, VIOTM, qpd test conditions..........................................................................................................8

• Corrected ground symbols for "Input (Devices with F suffix)" in Section 7.4.1 ................................................20

• Fixed Figure 8-2 INPUT wire connection..........................................................................................................22

• Added Section 8.2.3.1 sub-section under Section 8.2.3 section...................................................................... 23

• Added 'How to use isolation to improve ESD, EFT, and Surge immunity in industrial systems' to Section 9.1

section.............................................................................................................................................................. 26

Changes from Revision A (December 2016) to Revision B (March 2017)

Page

• Added D-8 values for TUV..................................................................................................................................9

• Changed the Electrostatic Discharge Caution statement ................................................................................ 26

Changes from Revision * (November 2016) to Revision A (December 2016)

Page

• Changed Feature From: IEC 60950-1, IEC 60601-1 and IEC 61010-1 End Equipment Standards To: IEC

60950-1 and IEC 60601-1 End Equipment Standards....................................................................................... 1

• Added Climatic category.....................................................................................................................................8

• Updated CSA column and changed DW package to (DW-16)........................................................................... 9

www.ti.com

ISO7710

SLLSER9E – NOVEMBER 2016 – REVISED DECEMBER 2024

Copyright © 2024 Texas Instruments Incorporated

Submit Document Feedback

27

Product Folder Links: ISO7710