BD9DA00MF datasheet(46/53 Pages) ROHM

46 / 53 page

46/50

BD9DA00MF

Datasheet

TSZ02201-0J2J0AB01940-1-2

18.Mar.2025 Rev.001

www.rohm.com

TSZ22111 • 15 • 001

Operational Notes

Reverse Connection of Power Supply

Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when

connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply

pins.

Power Supply Lines

Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at

all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic

capacitors.

Ground Voltage

Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. However,

pins that drive inductive loads (e.g. motor driver outputs, DC-DC converter outputs) may inevitably go below ground

due to back EMF or electromotive force. In such cases, the user should make sure that such voltages going below

ground will not cause the IC and the system to malfunction by examining carefully all relevant factors and conditions

such as motor characteristics, supply voltage, operating frequency and PCB wiring to name a few.

Ground Wiring Pattern

When using both small-signal and large-current ground traces, the two ground traces should be routed separately but

connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal

ground caused by large currents. Also ensure that the ground traces of external components do not cause variations

on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.

Recommended Operating Conditions

The function and operation of the IC are guaranteed within the range specified by the recommended operating

conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical

characteristics.

Inrush Current

When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow

instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply.

Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing

of connections.

Testing on Application Boards

When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject

the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should

always be turned off completely before connecting or removing it from the test setup during the inspection process. To

prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and

storage.

Inter-pin Short and Mounting Errors

Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in

damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.

Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and

unintentional solder bridge deposited in between pins during assembly to name a few.

Unused Input Pins

Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and

extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge

acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause

unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power

supply or ground line.

BD9DA00MF Datenblatt(PDF) 46 Page - Rohm

BD9DA00MF Datenblatt(HTML) 46 Page - Rohm

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

Datenblatt Download

Link URL